Dake Euromatic 370 S Скачать руководство пользователя страница 8

Страница: 8 / 64

370 S 370 S L 370 PP 370 PP L

WARNING!!!!!

Before performing the following operations, the electrical supply must be LOCKED OUT.

NEVER ATTEMPT TO CUT STEEL OR FERROUS MATERIALS WITH THE NON-FERROUS

HEAD INSTALLED. IT MAY CAUSE SERIOUS INJURY, OR FIRE!

CAUTION!!!!

USE CARE, CARBIDE TIPS ARE SHARP.

BLADE INSTALLATION

A: Clean spindle and flange faces, so there are no chips on the faces.

B. Remove item B using wrench d, put wrench D on shaft C. Then use wrench E to remove bolt F. (

Left Hand

Threads).

C: Install blade on the spindle shaft shoulder, so the teeth are facing down, for clockwise rotation, and install blade

flange. Take care that you do not hit any machine parts with the carbide tips; this may affect the blade performance.

D: Screw the spindle bolt in finger tight

E: Holding the spindle shaft with the wrench tighten bolt securely.

F: Close and tighten blade cover.

NOTE

: The blade pins may have been removed from your blade flange, to allow easier blade sizing, and safety. If you

reinstall the pins for carbide blade or HSS blade cutting, backlash must be removed from the blade while installing. See the

section on blade installation on page 0 of this manual.

Continued on page 11

Содержание Euromatic 370 S

































































Результаты поиска

Содержание Euromatic 370 S

Отзывы:

Похожие инструкции для Euromatic 370 S

Бренды по названию

Популярные бренды

Dake Euromatic 370 S, Инструкция по эксплуатации

Результаты поиска

Содержание Euromatic 370 S

Отзывы:

Похожие инструкции для Euromatic 370 S

Бренды по названию

Популярные бренды