Daikin RoCon HP Скачать руководство пользователя страница 3

x

 Safety

Daikin RoCon HP 
Daikin Control
008.1420844 – 05/2014

Operating instructions

3

1

Safety

1.1

Observing instructions

These instructions are a >> 

Translation of the original 

version

 << in your language.

All the activities required for operation and setting the parameters 
are described in this instruction manual. All parameters needed 
for trouble-free operation have been configured at the factory.

Please read through this manual carefully before operating 
the heating system or before adjusting the settings for it.

Make a note of the preset values before you make any 
changes to the unit configuration.

Relevant documents

– Daikin Altherma EHS(X/H):

– Operating instructions for the user/owner
– Installation and maintenance instructions
– Commissioning checklist

– External unit for Daikin Altherma EHS(X/H); the associated 

installation and operating instructions.

– When connecting to a Daikin solar system; the associated 

installation and operating instructions.

– If a Daikin FWXV(15/20)AVEB is connected; the associated 

installation and operating instructions.

– If a different Daikin heater or optional accessories are con-

nected; the associated installation and operating instructions.

The guides are included in the scope of supply for the individual 
units.

1.2

Warning signs and explanation of symbols

Meaning of the warnings

Warnings in this manual are classified according into their se-
verity and probability of occurrence.

DANGER!

Draws attention to imminent danger.

Disregarding this warning can lead to serious injury or 
death.

WARNING!

Indicates a potentially dangerous situation.

Disregarding this warning can result in serious injury 
or death.

CAUTION!

Indicates a situation which may cause possible 
damage.

Disregarding this warning can lead to damage to 
property and the environment.

This symbol identifies user tips and particularly useful 
information, but not warnings or hazards.

Special warning signs

Some types of danger are represented by special symbols:

Electric power

Risk of burning or scalding

Validity

Some information in this manual has limited validity. The validity 
is highlighted by a symbol.

Only valid for Daikin Altherma EHS(X/H) with cooling 
function

Valid/available only if a room station (EHS157034) is 

connected

Valid/available only if a mixer module (EHS157068) is 
connected

Handling instructions

Instructions on actions are shown as a list. Actions of which 
the sequential order must be maintained are numbered.

Results of actions are identified with an arrow.

Display readouts of the RoCon-Control

Entry into a setting procedure

Exit from a setting procedure

Certain screen displays or menu points may differ from those 
shown in these instructions due to country or equipment varia-
tions in the Daikin Altherma EHS(X/H) or the status of the user 
logged onto the Control.

1.3

Avoid danger

The Daikin Altherma EHS(X/H) is state-of-the-art and is built to 
meet all recognised technical requirements. However, improper 
use may result in serious physical injuries or death, as well as 
property damage. 

To avoid danger, only operate the Daikin Altherma EHS(X/H):
– as stipulated and in perfect condition,
– with an awareness of the safety and hazards involved.

This assumes knowledge and use of the contents of this manual, 
the relevant accident prevention regulations and the recognised 
safety-related and occupational medical rules.

WARNING!

This unit is not intended for use by persons (including 
children) with impaired physical, sensory or mental 
faculties or persons with insufficient experience and/or 
expertise unless supervised by a person responsible 
for ensuring their safety or are given instruction by this 
person on how to use the unit.

Содержание RoCon HP





















































Отзывы: