Daikin RoCon+ HP Series, Руководство по эксплуатации

Страница: 33 / 516

7 Parameter settings
Operating Instructions
33
Daikin RoCon+ HP
Daikin controller RoCon+ HP1
008.1447899_00 – 09/2019 – EN
Parameters Setting range
Min / Max
Description Factory
setting
Incre-
ment
Access
BE HF
Indoor unit No selection Heat pump interior unit type.
Adaptation of the set value important, as the device types have different
defrosting logics.
- - N E
ETS(H/X)
(B)16P30D
ETS(H/X)
(B)16P50D
Heating sys-
tem (*) Floor heating Heat exchanger type in the heating system.
If "Radiator" is selected and high feed temperatures are desired, it may
make sense to increase the [Max. feed temperature] parameter to 65 °C
([→ Main menu → Configuration → Heating]).
- N E
Convector
Radiator
Pump dT heat-
ing (*) 3 – 10 Required temperature difference between return and feed temperature. If a
minimum temperature difference is required for good heat distribution sys-
tem operation in heating mode. 5 1 N E
Pump dT cool-
ing (*) 3 – 10 Required temperature difference between return and feed temperature. If a
minimum temperature difference is required for good heat distribution sys-
tem operation in cooling mode. 5 1 N E
Glycol (*) No glycol added Adding glycol to the water circuit is recommended to guarantee frost pro-
tection in the event of a power failure. If glycol has been added to the sys-
tem, the RoCon+ controller setting must be adapted accordingly.
- N E
Glycol added
HP Power lim-
itation 20 – 50 A The permanent power limitation is useful to ensure maximum power con-
sumption of the system. In some countries, legislation limits the maximum
power consumption for room heating and domestic hot water. 50 A N E
Pump limit This parameter defines the maximum pump speed. Under normal condi-
tions, the default setting should NOT be changed. The limitation of the
pump speed is skipped if the flow rate is in the range of the minimum flow
rate. The water flow resulting at limited pump speed can be taken from the
pump characteristic curve (see Installation and maintenance instructions
Daikin Altherma ETS(X/H)) 6 1 N E
0 No limit
1 – 4 Limitation of pump speed independent of the operating status. This setting
cannot guarantee heating comfort. The maximum pump speed depends on
the setting as follows: 1: 90%, 2: 75%, 3: 65%, 4: 55%
5 – 8 Limitation of the pump speed if there is no heating or cooling requirement.
The maximum pump speed depends on the setting as follows: 5: 90%,
6: 75%, 7: 65%, 8: 55%
Tab. 7-9 Parameter in the "System" menu
7.5.3 Menu: External heat source
[→ Main menu → Settings → Ext. source]
Parameters Setting range
Min / Max
Description Factory
setting
Incre-
ment
Access
BE HF
Config. ext.
heat source Setting of whether there is an additional external heat generator for do-
mestic hot water preparation (DHW) and/or heating support (HZU). - N E
No external heat
generator The heat pump is the only heat source
Backup heater
BUH Optional heating rod (3N~) installed in the storage tank
DHW + heating
support An alternative heat generator (e.g. backup heater 1N~) provides domestic
hot water preparation and backup heating
Two external
heat generators Two external heat generators: Alternative WEZ 1 (e.g. backup heater 1N~)
takes over domestic hot water preparation and alternative WEZ 2 takes
over heating support
External power
hot water 1 – 40 kW Heat output of the electric heater booster for domestic hot water prepara-
tion 3 kW 1 kW N E
External power
stage 1 (*) 1 – 40 kW Heat output of the electric heater booster for heating support stage 1
See operating instructions for heating element EKBUxx.
3 kW 1 kW N E
External power
stage 2 (*) 1 – 40 kW Heat output of the electric heater booster for heating support stage 2
See operating instructions for heating element EKBUxx.
3 kW 1 kW N E