Daikin Magnitude WME Series Скачать руководство пользователя страница 8

Страница: 8 / 60

IOM 1266-2 • MAGNITUDE

MODEL WME CHILLERS

www.DaikinApplied.com

nsTallaTIon

Nameplates

There are several identification nameplates on the chiller:

• The unit nameplate is located on the exterior of the Unit

Control Panel. Both the Model No. and Serial No. are

located on the unit nameplate; the Serial No. is unique to

the unit. These numbers should be used to identify the

unit for service, parts, or warranty questions. This plate

also has the unit refrigerant charge and electrical ratings.

• Vessel nameplates are located on the evaporator and

condenser. They have a National Board Number (NB)

and a serial number, either of which identify the vessel

(but not the entire unit).

Receiving and Handling

The unit should be inspected immediately after receipt for

possible damage. All Daikin Applied centrifugal water chillers

are shipped FOB factory and all claims for handling and

shipping damage are the responsibility of the consignee.
On units with factory-installed insulation, the insulation

is removed from the vessel lifting hole (also used for

transportation tie-downs) locations and is shipped loose. It

should be secured in place after the unit is finally placed.

Neoprene vibration isolation pads are shipped loose in the

power panel. If the unit is equipped with a shipping skid, leave

the skid in place until the unit is in its final position. This will aid

in handling the equipment.

CAUTION

Extreme care must be used when rigging the unit to prevent

damage to the control panels and refrigerant piping. See the

certified dimension drawings included in the job submittal for

the weights and center of gravity of the unit. If the drawings

are not available, consult the local Daikin Applied sales office

for assistance.

The unit can be lifted by fastening the rigging hooks to the four

corners of the unit where the rigging eyes are located, see

Figure 5

. A spreader bar must be used between the rigging

lines to prevent damage to the control panels, piping, and

electrical panels. The spreader bar length should be equal

to, or no more than 1-foot shorter than, the distance between

the lifting holes located at opposite ends of the chiller. The

unit will require a single spreader bar of this length capable

of supporting 1.5 times the shipping weight of the unit.

Separately, all cables and hooks by themselves must also be

capable of supporting 1.5 times the shipping weight of the unit.

NOTE:

The spreader bars in

Figure 5

are a representation

only and may not reflect the appearance of the actual

spreader bars needed.

If a knockdown option was ordered on the unit, reference the

“Retrofit Knockdown”

section starting on

page 11

for more

information.

Location

WME chillers are intended only for installation in an indoor or

weather protected area consistent with the NEMA 1 rating on

the chiller, controls, and electrical panels. Equipment room

temperature for operating and standby conditions is 40°F to

104°F (4.4°C to 40°C).

NOTE:

Excessive humidity in the mechanical room should

be avoided. A limit of 90% non-condensing humidity

should be met to minimize electrical components

exposure to water condensing in panels. Humidity

levels in the mechanical room, even if lower than

90%, can cause water to condense on/near all cool

surfaces and potentially lead to premature component

wear. If possible, the mechanical room should be

conditioned which can extend the useful lifetime for

all mechanical room equipment.
Radiant heat from boilers or piping that would

adversely raise component surface temperatures

beyond ambient limits must also be avoided.

Figure 5: WME Unit Rigging

LIFT CONTROL BOX WITH

1/2" LIFTING EYES (QYT 2)

NOT SUPPLIED

LIFT VFD WITH LIFTING EYES

(QTY 4)

LIFT FULL UNIT OR INDIVIDUAL EVAPORATOR & CONDENSER FROM TUBESHEET

ROUND LIFTING HOLES. USE SPREADER BARS TO KEEP LIFT STRAPS VERTICAL.

LIFT COMPRESSOR WITH M16

LIFTING EYES (QTY 2)

NOT SUPPLIED

WME-C VINTAGE DUAL UNIT

910222350

DAIKIN APPLIED IS NOT A LICENSED NOR

CERTIFIED RIGGING SPECIALIST.

THEREFORE IT IS THE CUSTOMERS

RESPONSIBILITY TO CONSULT A CERTIFIED

RIGGING CONTRACTOR TO RIG, LIFT, AND

MOVE COMPONENTS & SUBCOMPONENTS

PROPERLY AND SAFELY AS NEEDED.

Содержание Magnitude WME Series





























































Результаты поиска

Содержание Magnitude WME Series

Отзывы:

Похожие инструкции для Magnitude WME Series

Бренды по названию

Популярные бренды

Daikin Magnitude WME Series, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание Magnitude WME Series

Отзывы:

Похожие инструкции для Magnitude WME Series

Бренды по названию

Популярные бренды