manualshive.com logo in svg

Daikin Magnitude WME Series, Инструкция по установке, эксплуатации и обслуживанию

Поделиться
Скачать
Daikin Magnitude WME Series Скачать руководство пользователя страница 11

I

nsTallaTIon

www.DaikinApplied.com 11 

IOM 1266-2 • MAGNITUDE

®

 MODEL WME CHILLERS

Retrofit Knockdown

Magnitude

®

 WME chillers are relatively easy to disassemble due to the small compressor size, simplified refrigerant piping, and 

the absence of a lubrication system with its attendant components and piping. Various knockdown arrangements are available as 

options and are ideal for retrofit applications with tight installation clearances. 

Bolt-Together Construction - Type A

Chillers are built and shipped completely assembled with bolt-together construction on major components for field disassembly and 

reassembly on the job site. 

Figure 8: Bolt-Together Construction Option - Representative Schematic    

 

Scope:

•  Site disassembly and reassembly must be supervised or 

completed by Daikin Applied service personnel. 

•  Unit is fully tested at the factory prior to shipment.
•  The chiller is shipped completely assembled with the 

full refrigerant charge, which must be recovered before 

breaking any refrigerant connection. 

•  The refrigerant charge must be removed from the unit 

if the vessels are to be separated. Exert the proper 

precautions before attempting any disassembly, assume 

the condenser isolation valves may have leaked and that 

any component of the chiller may be pressurized with 

refrigerant. 

• 

Suction and discharge lines have bolt-on flanges.

•  Motor cooling line is brazed at mechanical connections.

•  Blockoff plates are required to cover any refrigerant 

connection left open for extended periods of time. Contact 

Daikin Applied service to obtain these parts.

•  Check that no power is being applied to the unit. Before 

disconnecting any wire, it is prudent to label its function 

and connection point to facilitate reconnection.

•  Unit ships with vessel and/or head insulation, if ordered.
•  Unit ships with replacement refrigerant gaskets and 

O-rings, stick-on wire ties, and touch-up paint. Some 

insulation repair and touch-up painting may be required.

 CAUTION

Standard torque specs must be followed when re-installing 

bolts. Contact Daikin Applied service for this information.

VESSEL 

BREAKPOINTS 

TYP. (IF NEEDED)

UNIT 

CONTROL 

BOX

HMI PANEL BOXED AND 

SECURELY STRAPPED 

TO UNIT CONTROL BOX 

FOR SHIPPING

POWER BOX

NOTE: ALL STEEL PIPING & 

COPPER TUBING IS DESIGNED 

WITH MECHANICAL BREAKPOINTS

Содержание Magnitude WME Series





























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды