Daikin Magnitude WME Series Скачать руководство пользователя страница 48

Страница: 48 / 60

IOM 1266-2 • MAGNITUDE

MODEL WME CHILLERS

48 www.DaikinApplied.com

peraTIon

Table 23: Critical Alarms

Screen Text

Trigger Condition

Low Evaporator Pressure

Evaporator Pressure (or lowest Suction Pressure if Evaporator Pressure Transducer is detected as bad or disconnected)

is less than Low Evaporator Pressure Alarm Setpoint. Causes: Low or No Evaporator Water Flow. Low refrigerant level in

evaporator. Incorrect setpoint value for leaving water temperature.

High Condenser Pressure

Condenser Pressure (or Highest Discharge Pressure if Condenser Pressure Transducer is detected as bad or

disconnected) is greater than 160 PSI

Evaporator Pressure Sensor Fault

Evaporator Pressure Transducer and Suction Pressure Transducer(s) are detected as bad or disconnected

Condenser Pressure Sensor Fault

Condenser Pressure Transducer and Discharge Pressure Transducer(s) are detected as bad or disconnected

Evaporator Water Flow Loss

An alarm occurs while Evaporator Flow is not detected. Causes: Loss of evaporator flow, evaporator pump off, evap head

gasket leaking or missing, sensor wiring fault, evaporator flow sensor failure

Condenser Water Flow Loss

An alarm occurs while Condenser Flow is not detected. Causes: Loss of condenser flow, condenser pump off, condenser

head gasket leaking or missing, sensor wiring fault, condenser flow sensor failure

Evaporator Pump Fault

Evaporator pump does not see flow for 60 seconds after turning on when evaporator pump control is enabled.

Condenser Pump Fault

Condenser pump does not see flow for 60 seconds after turning on when condenser pump control is enabled.

Evaporator Freeze Protect

Saturated Evaporator Temperature is less than Evaporator Freeze Protection Setpoint while chiller is OFF.

Causes: Low evaporator water flow rate, low refrigerant in chiller.

Condenser Freeze Protect

Saturated Condenser Temperature is less than Condenser Freeze Protection Setpoint while chiller is OFF.

Causes: Low condenser water flow rate, low refrigerant in chiller.

MicroTech OFFLINE Error

The MicroTech on the compressor controller is offline (no comm/power)

MicroTech Configuration Error

The MicroTech on the compressor controller has a configuration error

VFD Communications Fault

Communication between the compressor controller and the VFD are interrupted

MBC Communications Fault

Communication between the compressor controller and the MBC are interrupted

Low Suction Pressure

Suction Pressure is less than Low Suction Pressure setpoint and Suction Pressure Warning is not active

High Discharge Pressure

Discharge pressure > High Discharge Pressure SP. Causes: Low or No Condenser Water Flow

Discharge Temperature High

Discharge Pressure is greater than 160 PSI and Discharge Pressure Sensor Warning is not active. Causes: Low or No

Condenser Water Flow

High Motor Winding Temperature

One of the motor winding temperatures is greater than 298 F. Causes: Motor stator cooling solenoid not open, rotor cooling

stepper motor not functioning correctly, motor rotor superheat or gain setpoints incorrect (contact factory)

High Motor Gap Temperature

Motor Gap Temperature is greater than 130F

Max RLA Exceeded

VFD Output exceeds 115% of Nameplate RLA Setpoint

Motor Gap Temperature Sensor Fault

Motor Gap Temperature Sensor is detected as bad or disconnected

Rotor Pump Temperature Sensor Fault

Rotor Pump Temperature Sensor is detected as bad or disconnected

Motor Winding Temperature Sensor Fault

All Motor Winding Temperature Sensors are detected as bad or disconnected

High Suction Temperature Fault

Suction Temperature is greater than 125F and Suction Temperature Sensor Warning is not active

High Discharge Temperature Fault

Discharge Temperature is greater than 150F and Discharge Temperature Sensor Warning is not active

VFD Fault

A Fault occurs from the VFD

MBC Fault

A Fault occurs from the MBC

Table 24: Warning Alarms

Screen Text

Trigger Condition

Evaporator Pressure Sensor Warning

Evaporator Pressure Transducer is detected as bad or disconnected but there are valid Suction Pressure Transducer(s)

detected

Condenser Pressure Sensor Warning

Condenser Pressure Transducer is detected as bad or disconnected but there are valid Discharge Pressure Transducer(s)

detected

Motor Case Temperature Sensor

Warning

Motor Case Temperature Sensor is detected as bad or disconnected

Motor Winding Temperature Sensor

Warning

Two of the Motor Winding Temperature Sensors are detected as bad or disconnected

Suction Temperature Sensor Warning

Suction Temperature Sensor is detected as bad or disconnected

Discharge Temperature Sensor

Warning

Discharge Temperature Sensor is detected as bad or disconnected

Suction Pressure Sensor Warning

Suction Pressure Sensor is detected as bad or disconnected

Discharge Pressure Sensor Warning

Discharge Pressure Sensor is detected as bad or disconnected

MBC Warning

A Warning occurs from the MBC

Содержание Magnitude WME Series





























































Результаты поиска

Содержание Magnitude WME Series

Отзывы:

Похожие инструкции для Magnitude WME Series

Бренды по названию

Популярные бренды

Daikin Magnitude WME Series, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание Magnitude WME Series

Отзывы:

Похожие инструкции для Magnitude WME Series

Бренды по названию

Популярные бренды