Daikin Magnitude WME Series Скачать руководство пользователя страница 12

Страница: 12 / 60

IOM 1266-2 • MAGNITUDE

MODEL WME CHILLERS

12 www.DaikinApplied.com

nsTallaTIon

Partial Disassembly Construction - Type B

Compressor(s), power box(es), and control box are removed at the factory and shipped on separate skids; combined vessel stack

is shipped together as a sub-assembly.

Figure 9: Partial Disassembly Construction Option - Representative Schematic

Scope:

• Site reassembly must be supervised or completed

by Daikin Applied service personnel. Cost for unit

reassembly and supervision by Daikin Applied service

is not included in the purchase price of the equipment.

Contact Daikin Applied service for pricing.

• Unit is fully tested at the factory prior to disassembly and

shipment.

• All associated piping and wiring remain attached, if

possible. Suction and discharge lines have bolt-on

flanges and, if possible, remain attached. If the stack size

or weight dictates further disassembly, the vessels can

be separated by disconnecting any interconnecting wiring

and tubing and then unbolting them.

• Refrigerant will not be shipped with the chiller and must

be procured by others. Compressor(s) and vessels

receive an inert gas holding charge that must be released

prior to attempting to open any connection.

• All free piping ends are capped. Blockoffs will cover all

compressor and vessel openings.

• Unit ships with vessel and/or head insulation, if ordered.
• Unit ships with replacement refrigerant gaskets and

O-rings, stick-on wire ties, and touch-up paint.

CAUTION

Standard torque specs must be followed when re-installing

bolts. Contact Daikin Applied service for this information.

WARNING

Remove compressor, piping or vessel holding charge through

the Schrader valve in the blockoff plates before attempting to

loosen any fittings on them. Failure to do so can cause severe

bodily injury.

COMPRESSOR

(x2 FOR DUAL COMPRESSOR MODELS)

* DUAL COMPRESSOR VESSEL BLOCKOFFS SHOWN

FOR REPRESENTATIVE ILLUTRATION - SINGLE

COMPRESSOR MODELS WILL HAVE 1 SET.

VESSEL

BREAKPOINTS

VESSEL

BREAKPOINTS

BLOCKOFF

VESSEL

NOZZLE*

32:(5%2;

5(35(6(17$7,9(6+2:1

(x2 FOR DUAL COMPRESSOR MODELS)

GLUE

INSULATION & OTHER ITEMS

MISCELLANEOUS ITEMS

CRATE 1

Y'03%6"-$0.13&4403.0%&-4

LIQUID INJECTION

CRATE 2

Y'03%6"-$0.13&4403.0%&-4

DISCHARGE PIPING

ROTOR COOLING SUPPLY (3 PCS) & RETURN LINE

STATOR COOLING SUPPLY (2 PCS) & RETURN LINE

SUCTION ELBOW

MAIN LIQUID LINE

LOOSE INSULATION

-*26*%-*/&&&7#0%:

3"/(&&95&/4*0/1*1*/(

GLUE

MISCELLANEOUS ITEMS

Содержание Magnitude WME Series





























































Результаты поиска

Содержание Magnitude WME Series

Отзывы:

Похожие инструкции для Magnitude WME Series

Бренды по названию

Популярные бренды

Daikin Magnitude WME Series, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание Magnitude WME Series

Отзывы:

Похожие инструкции для Magnitude WME Series

Бренды по названию

Популярные бренды