manualshive.com logo in svg

Daikin E8.5064, Руководство по установке

Поделиться
Скачать
Daikin E8.5064 Скачать руководство пользователя страница 28

Installation level 

 

Input of the basic setting

 

28 

 

Solar/MF 

Designation Value 

range 

Default 

IV 

RELAY FUNC (1-4)  00 - 26 

00,00,01,02   

T-MF(1-4) SETP 

30 °C - 90 °C  30 °C 

 

MF(1-4) HYST 

2 K - 10 K 

5 K 

 

F15 FUNCTION 

00 - 03 

00 

 

See following pages for continuation 

 

Auxiliary relay functions 

 
The multifunction relays = MF relay is assigned one basic func-
tion respectively 

MF-1: Mixer HC1 OPEN (FUNC RELAY 1 = 00) 
MF-2: Mixer HC1 CLOSED (FUNC RELAY 2 = 00) 
MF-3: Header pump (FUNC RELAY 3 = 01) 
MF-4: Circulation (time) (FUNC RELAY 4 = 02) 

If this basic function of a MF relay is not required (configuration of 
the installation in Installation level), any one of the functions de-
scribed below may be selected for any unused relay. 

The MF-relay   1 - 4 (A8-A11) is always assigned with a sensor   
1 - 4 (F11-F14) (applies for functions starting from „20“ only). If a 
further sensor is required for a function, this sensor must be con-
nected as F17 (connector III, Pin 2 + 3).  
The functions that may be selected for the MF relays   1 - 4 are 
described using MF relay 1 as an example. 

RELAY FUNC 1

 (function selection relay MF1)

 

T-MF1 SETP

 (switching temperature relay MF1)

 

MF 1 HYST

 (hysteresis relay MF1)

 

 

00 = No MF function 

 

01 = Header pump 

 
ON: When heat is requested by a consumer 
OFF: Without consumer heat request 
If at least one consumer in the system requests heat the pump is 
switched on. The after-run function runs after the burner has been 
switched on. 

02 = Circulation (time) 

 
Switching the relay according to the time program for the circula-
tion pump 

03 = Booster pump 

 
ON: When heat is requested by an internal consumer 
OFF: When no heat is requested by an internal consumer. Fol-
low-up pump action occurs. 

05 = Pump HS1 

 
The relay may be used to control boiler pump for heat genera-
tor 1. 
(Relay switches with burner relay 1; run-down = 5 min) 

Содержание E8.5064

















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды