manualshive.com logo in svg

Daikin E8.5064, Руководство по установке

Поделиться
Скачать
Daikin E8.5064 Скачать руководство пользователя страница 16

Remote controls 

 

Installation

 

16 

 

Sensor values/characteristic curve 

 

Temperature  5 kOhm NTC  1 kOhm PTC  PT1000 

-60 °C 

698961 

 470 

 

-50 °C 

333908 

 520 

 

-40 °C 

167835 

 573 

 

-30 °C 

88340 

 630 

 

-20 °C 

48487 

 690 

 922 

-10 °C 

27648 

 755 

 961 

0 °C 

16325 

 823 

 1000 

10 °C 

9952 

 895 

 1039 

20 °C 

6247 

 971 

 1078 

25 °C 

5000 

 1010 

 1097 

30 °C 

4028 

 1050 

 1118 

40 °C 

2662 

 1134 

 1155 

50 °C 

1801 

 1221 

 1194 

60 °C 

1244 

 1312 

 1232 

70 °C 

876 

 1406 

 1270 

80 °C 

628 

 1505 

 1309 

90 °C 

458 

 1607 

 1347 

100 °C 

339 

 1713 

 1385 

110 °C 

255 

 1823 

 1422 

120 °C 

194 

 1936 

 1460 

 

 

5 kOhm NTC: AF, KF, SPF, VF 

1 kOhm PTC: AFS, KFS, SPFS, VFAS 

 

The controller can be operated with 5 kOhm NTC (stand-
ard) or 1 kOhm PTC sensors. The sensor type is selected 
in the start-up level during start-up. 

The start-up level is displayed when the operating cover is 
opened after the supply voltage has been switched on  
(once only). It can be reactivated again by briefly switching 
the supply voltage off. 

The sensor switchover affects all sensors.  

Exceptions: 

  Attaching an analogue remote control is detected au-

tomatically. This means that the previous and new ver-
sions can be connected to the controller [connector I; 
2, ground, 3 and connector III; 1 - 3]. 

Содержание E8.5064

















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды