Daikin E8.5064 Скачать руководство пользователя страница 17

Страница: 17 / 48

Installation

Sensors

Outside sensor AF (AFS)

Order no. AF, 5 k

Ω

: 99 679 030

Order no. AFS, 1 k

Ω

: 99 679 001

Scope of supply

Outside sensor, screw and dowel

Installation location:



Wherever possible, on a northerly or north-easterly

wall behind a heated room



Approx. 2.5 m above ground



Not above windows or ventilation shafts

Installation:



Pull cover off sensor.



Fasten sensor with enclosed screw



Connect

electrically

Immersion sensor KF (KFS)

/SPF (SPFS)

Order no. KF/SPF, 5 k

Ω

, 3 m, ø 6.0x50: 99 676 769

Order no. KFS/SPFS, 1 k

Ω

, 3 m, ø 6.0x50: 99 676 682

Installation location:



In the immersed pipe of the hot-water cylinder tank

(generally on the front face of the tank)

Installation:



Slide the sensor as far as possible into

the immersed pipe.

The immersed sleeve must be dry.



Connect

electrically

Strap-on sensor VF (VFAS)

Order no. VF, 5 k

Ω

, 3 m, ø 6.0x50: 99 679 073

Order no. VFAS, 1 k

Ω

, 3 m, ø 6.0x50: 99 679 051

Scope of supply

Flow sensor, thermal compound, retaining strap, pressure
cap

Installation location:



In the case of boiler control instead of the boiler sensor

KF as close as possible behind the boiler on the heat-
ing flow pipe



In the case of mixer operation

approx. 0.5 m behind

the circulation pump

Installation:



Thoroughly clean the flow pipe.



Apply heat conductive paste (A)!!



Secure sensor with stretch band.



Connect

electrically

Only sensor of one type may be used

Содержание E8.5064

















































Результаты поиска

Содержание E8.5064

Отзывы:

Бренды по названию

Популярные бренды

Daikin E8.5064, Руководство по установке

Результаты поиска

Содержание E8.5064

Отзывы:

Бренды по названию

Популярные бренды