Daikin DM96SE, Руководство по установке

Страница: 20 / 40

20
9. Install the non-grommet end of hose #11 from
outside the cabinet in the upper drain hole. Install
on collector box and secure with a silver clamp.
10. Use two silver clamps and secure the hoses to drain
trap. The trap outlet faces the front of the furnace.
Secure the
trap to the cabinet using two screws removed in step
2 by inserting the two screws through the large set of
holes in
the top mounting tabs of the trap into the two predrilled
holes in the side of the cabinet.
E
LECTRICAL
C
ONNECTIONS
E
DGES OF SHEET METAL HOLES MAY BE SHARP
. U
SE GLOVES AS A
PRECAUTION WHEN REMOVING HOLE PLUGS
.
WARNING
T
O PREVENT PERSONAL INJURY OR DEATH DUE TO ELECTRIC SHOCK
,
DISCONNECT ELECTRICAL POWER BEFORE INSTALLING OR SERVICING THIS
UNIT
.
WARNING
HIGH VOLTAGE !
T
O AVOID THE RISK OF INJURY
,
ELECTRICAL SHOCK OR
DEATH
,
THE FURNACE MUST BE ELECTRICALLY
GROUNDED IN ACCORDANCE WITH LOCAL CODES OR IN
THEIR ABSENCE
,
WITH THE LATEST EDITION OF THE
N
ATIONAL
E
LECTRIC
C
ODE
.
WARNING
W
IRING
H
ARNESS
The wiring harness is an integral part of this furnace. Wires
are color coded for identification purposes. Refer to the wiring
diagram for wire routings. If any of the original wire as sup-
plied with the furnace must be replaced, it must be replaced
with wiring material having a temperature rating of at least
105° C. Any replacement wiring must be a copper conductor.
115 V
OLT
L
INE
C
ONNECTIONS
Before proceeding with electrical connections, ensure that the
supply voltage, frequency, and phase correspond to that speci-
fied on the unit rating plate. Power supply to the furnace must
be NEC Class 1, and must comply with all applicable codes. The
furnace must be electrically grounded in accordance with local
codes or, in their absence, with the latest edition of The Na-
tional Electric C
ode, ANSI NFPA 70 .
Use a separate fused branch electrical circuit containing prop-
erly sized wire, and fuse or circuit breaker. The fuse or
circuit breaker must be sized in accordance with the maxi-
mum overcurrent protection specified on the unit rating plate.
An electrical disconnect must be provided at the furnace
location.
Connect hot, neutral, and ground wires as shown in the wir-
ing diagram located on the unit’s blower door. For direct
vent applications, the cabinet opening to the junction box
must be sealed air tight using either an UL approved bushing
such as Heyco Liquid Tight or by applying non-reactive UL
approved sealant to bushing.
Line polarity must be observed when making field connec-
tions. Line voltage connections can be made through either
the right or left side panel. The furnace is shipped config-
ured for a right side electrical connection with the junction
box located inside the burner compartment. To make elec-
trical connections through the opposite side of the furnace,
the junction box must be relocated to the other side of the
burner compartment prior to making electrical connections.
To relocate the junction box, follow the steps shown below.
NOTE: Wire routing must not to interfere with circulator
blower operation, filter removal, or routine maintenance.
Heyco Liquid Tight or by applying non-reactive UL approved
sealant to bushing.
Line polarity must be observed when making field connec-
tions. Line voltage connections can be made through either
the right or left side panel. The furnace is shipped config-
ured for a right side electrical connection with the junction
box located inside the burner compartment. To make elec-
trical connections through the opposite side of the furnace,
the junction box must be relocated to the other side of the
burner compartment prior to making electrical connections.
To relocate the junction box, follow the steps shown below.
NOTE: Wire routing must not to interfere with circulator
blower operation, filter removal, or routine maintenance.
J
UNCTION
B
OX
R
ELOCATION
HIGH VOLTAGE !
T
O AVOID PERSONAL INJURY OR DEATH DUE TO
ELECTRICAL SHOCK
,
DISCONNECT ELECTRICAL POWER
BEFORE SERVICING OR CHANGING ANY ELECTRICAL
WIRING
.
WARNING
T
O PREVENT UNRELIABLE OPERATION OR EQUIPMENT DAMAGE
,
THE
GAS MANIFOLD PRESSURE MUST BE AS SPECIFIED ON THE UNIT RATING
PLATE
. O
NLY MINOR ADJUSTMENTS SHOULD BE MADE BY ADJUSTING
THE GAS VALVE PRESSURE REGULATOR
.
CAUTION