Daikin AGZ 190D Скачать руководство пользователя | Manualshive

Страница: 9 / 84

background image

OMM 1166-1

AGZ 025D through 190D

9

automatic through the ambient sensing
thermostat that energizes the evaporator heater
cable for protection against freeze-up. Unless

the evaporator is drained in the winter, the
disconnect switch to the evaporator heater
must not be open.

Operating/Standby Limits



Maximum standby ambient air temperature, 130



F (55



C)



Maximum operating ambient air temperature 105



F (40.6



C)



Minimum operating ambient temperature (standard), 35



F (2



C)



Minimum operating ambient temperature (with optional low-ambient control), -10



F (-23.3



C)



Leaving chilled water temperature, 40



F to 60



F (4.4



C to 15.6



C)



Leaving chilled fluid temperatures (with anti-freeze), 15



F to 60



F (-9.4



C to 15.6



C)



Chilled water Delta-T range, 6 degrees F to 16 degrees F (3.3 degrees C to 8.9 degrees



C)



Part load minimum flow for variable flow systems, varies with unit size; see Table 8, page 11.



Maximum operating inlet fluid temperature, 76



F (24



C)



Maximum non-operating inlet fluid temperature, 100



F (38



C).

Pressure Drop Curves

Minimum Allowable Flow Rates

In order to maximize energy savings from variable flow systems, the AGZD chiller employs different
control strategies for constant-f low chilled water systems as compared to variable-flow systems.

A chiller controller setpoint selects the proper controller operation. The software setting of Variable
Evap. Flow equals YES or NO is located just below the “Full Cap D-T” setting screen.

The Full Cap D-T setting will continue to allow settings from 6 to 16 F Delta-T for full load operation.

Constant-Chilled Water Flow Systems

The minimum allowable flow is determined by the chiller model. Operating with flows below these
values can cause unstable operation.

Variable-Chilled Water Flow Systems

For models AGZ 025D through AGZ 130D the part load flow rate in a variable chilled water flow
system is 40% of nominal catalog

full load

flow (rated catalog tons x 2.4 = full load GPM). These

minimum allowable flows are calculated to allow the chilled water flow to decrease progressively as
the unit capacity decreases, but is restricted to 40% of rated full load flow.

The larger AGZ 140D to190D units have shell and tube evaporators and will operate at the same
minimum flow rate as for constant flow (62.5% of nominal catalog full load flow rate.)

When “Variable Evap Flow” is selected as YES – the unit software will increase the control band
progressively as the unit capacity steps to the lower stages of 75%, 50% and 25% load for the four
compressors. This prevents short cycling and allows for decreasing minimum water flow as the unit
capacity decreases. The 6 compressor units will have a similar operation but with software
calculations based on 6 capacity steps.

Refer to Table 8 on page 11 for the allowable reduced minimum flows.

«
...
7
8
9
10
11
...
»

Содержание AGZ 190D





















































































Отзывы:

Нет отзывов

Похожие инструкции для AGZ 190D

OMNI OWC-5 Series

Бренд: Enviroheat Страницы: 70

DELTA II 9100 Series

Бренд: lancer Страницы: 28

Бренд: Troy-Bilt Страницы: 12

Бренд: Trane Страницы: 40

Бренд: Farmi Страницы: 106

Therminator 057.029.1

Бренд: Blichmann Engineering Страницы: 7

Бренд: Laird Страницы: 2

Бренд: FRIULAIR Страницы: 60

Бренд: Nakayama Страницы: 11

Бренд: Yaros Страницы: 24

Бренд: YARDMAX Страницы: 24

Бренд: Raider Страницы: 78

IDRA-RSC Series

Бренд: Fast Страницы: 32

Бренд: Gardol Страницы: 160

Бренд: LawnMaster Страницы: 28

Бренд: York Страницы: 156

R-407C Optimized

Бренд: York Страницы: 120

Бренд: York Страницы: 48

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды