Daikin AGZ 190D страница 69 Скачать руководство пользователя | Manualshive

Страница: 69 / 84

background image

OMM 1166-1

AGZ 025D through 190D

69

Compressor Communications

The communication module, installed in the 20 to 40 ton compressor electrical box, provides advanced
diagnostics, protection, and communications that enhance compressor performance and reliability.
Features include motor temperature protection, scroll temperature protection, missing phase
protection, reverse phase protection, low control circuit voltage protection, short cycling detection and
alert, modbus communication to system controller, operational and fault history storage, and LED
status display.

OPERATION

Warnings and Alerts

A

solid

g

reen LED

indicates the module is powered and operation is normal.

A

solid red LED

indicates an internal problem with the module.

A

flashing green LED

communicates

Warning

codes. Warning codes do not result in a trip or lockout

condition.
A

flashing red LED

communicates

Alert

codes.

Alert

codes will result in a trip condition and

possibly a lockout condition

Warning Codes (Flashing Green LED )

Code 1 – Loss of Communication: The module will flash the green

Warning

LED one time indicating

the module has not communicated with the master controller for longer than 5 minutes.

Code 2 – Reserved For Future Use

Code 3 – Short Cycling: The module will flash the green

Warning

LED three times indicating the

compressor has short cycled more than 48 times in 24 hours.

Code 4 – Open/Shorted Scroll Thermistor: The module will flash the green

Warning

LED four times

indicating an open/shorted

Alert/Lockout Codes (Flashing Red LED)

Code 1 – Motor High Temperature: The module will flash the red

Alert

LED one time indicating the

motor is onerheating . A code 1

Alert

will open the M2-M1 contacts. The

Alert

will reset after 30

minutes. Five consecutive Code 1

Alerts

will lockout the compressor. Once the module has locked out

the compressor, a power cycle or Modbus reset command will be required for the lockout to be
cleared.

Code 2 – Open/Shorted Motor Thermistor The module will flash the red

Alert

LED two times

indicating the motor PTC thermistor circuit has an open/shorted thermistor chain (see

Table 2

). A

Code 2

Alert

will open the M2-M1 contacts. The

Alert

will reset after 30 minutes and the M2-M1

contacts will close if the resistance of the motor PTC circuit is back in the normal range. The module

Green/Red LEDs

«
...
67
68
69
70
71
...
»

Содержание AGZ 190D





















































































Отзывы:

Нет отзывов

Похожие инструкции для AGZ 190D

Бренд: Kaysun Страницы: 57

Бренд: AGRI EASE Страницы: 46

Бренд: Carrier Страницы: 36

Бренд: LG Страницы: 77

Бренд: Troy-Bilt Страницы: 68

Бренд: Hansa Страницы: 29

Бренд: Farmi Forest Страницы: 48

Бренд: Daikin Страницы: 16

Бренд: TACKLIFE Страницы: 27

Бренд: Laird Страницы: 2

Maxxum HCCA Series

Бренд: Trane Страницы: 20

Бренд: UNIA Страницы: 34

Бренд: Cub Cadet Страницы: 20

Бренд: Yaros Страницы: 24

Бренд: Rally Страницы: 4

Бренд: ICS Страницы: 72

PTO MC100 Series

Бренд: YAAHKIEH Страницы: 32

Бренд: Garland Страницы: 160

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды