Daikin AGZ 190D страница 62 Скачать руководство пользователя

Страница: 62 / 84

AGZ 025D through 190D

OMM 1166-1

LCD Display

Table 16, Display Data

Name

Display

Content

Operation

Mode Menus

MODE

Displayed when in Mode Selection.

MONITR

Displayed when in Monitor Mode.

VERIFY

Indicates the Verify Menu

PRMSET

Displayed when in Parameter Setting Mode.

A.TUNE

Displayed during Auto-Tuning.

SETUP

Displayed when in Setup Mode.

DriveWorksEZ

Function

Selection

DWEZ

Displayed when DriveWorksEZ is set to enable. (A1-07 = 1 or 2)

Mode Display

Area

DRV

Displayed when in Drive Mode.

PRG

Displayed when in Programming Mode

Ready

Rdy

Indicates the drive is ready to run.

Data Display

—

Displays specific data and operation data.

FrequencyRef

erence

Assignment

<1>

OPR

Displayed when the frequency reference is assigned to the LCD Operator
Option.

Displayed when the frequency reference is assigned to the Analog Input of the
drive

COM

Displayed when the frequency reference is assigned to the MEMOBUS/Modbus
CommunicationInputs of the drive

Displayed when the frequency reference is assigned to an Option Unit of the
drive.

Displayed when the frequency reference is assigned to the Pulse Train Input of
the drive

LO/RE Display

<2>

RSEQ

Displayed when the run command is supplied from a remote source.

LSEQ

Displayed when the run command is supplied from the operator keypad.

RREF

Displayed when the run command is supplied from a remote source.

LREF

Displayed when the run command is supplied from the operator keypad

Function Key

1(F1)

JOG

Pressing [F1} executes the Jog function.

HELP

Pressing [F1] displays the Help menu.

←

Pressing [F1] scrolls the cursor to the left.

HOME

Pressing [F1] returns to the top menu (Frequency Reference).

ESC

Pressing [F1] returns to the previous display

FWD/REV

FWD

Indicates forward motor operation.

REV

Indicates reverse motor operation.

Function Key 2

(F2)

FWD/REV

Pressing [F2] switches between forward and reverse

DATA

Pressing [F2] scrolls to the next display

Pressing [F2] scrolls the cursor to the right

RESET

Pressing [F2] resets the existing drive fault error

Содержание AGZ 190D





















































































Результаты поиска

Содержание AGZ 190D

Отзывы:

Похожие инструкции для AGZ 190D

Бренды по названию

Популярные бренды

Daikin AGZ 190D, Руководство по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание AGZ 190D

Отзывы:

Похожие инструкции для AGZ 190D

Бренды по названию

Популярные бренды