Daewoo TACUMA Скачать руководство пользователя страница 78

Страница: 78 / 126

6–10 FRAME DOOR OPENING, DOOR AND SIDE PANEL OUTER

•

Grind both sides of the welding section of the pre-

pared side panel outer with a disk sander to re-
move the paint and expose the steel plate.

•

Clamp the new panel in place with the vise grips.

•

Tack weld the clamped section for temporary in-

stallation.

CAUTION: To prevent eye injury and burns when
welding, wear an approved welding helmet, gloves
and safety shoes.

•

Remove the vise grips and temporarily install the

trunk lid and doors, then check the clearances,
level differences and outer appearance.

6. Perform the main welding.

•

Weld the frame door opening area and pillar at the

butt joints with a gas or MIG welder.

•

Spot weld the flanges and wheel arch of the side

panel outer as shown.

CAUTION: To prevent eye injury and burns when
welding, wear an approved welding helmet, gloves
and safety shoes.

•

Perform a trial welding first, and check the weld-

ing condition.

•

Increase the number of spot by 20% for areas to

be spot welded.

Fig. 12

7. Finish the welding areas.

•

Level the gas or MIG welded areas with a disc

sander, then even out high areas with a hammer
being careful not to deform them.

CAUTION: To prevent eye injury, wear goggles or
safety glasses whenever sanding, cutting, or grind-
ing.

•

Use a hammer and dolly to even out the spot

welded flanges for a close fit with the surface of
the side panel outer.

•

Fill in deformations and level differences of the

welded areas with solder or putty, then finish.

8. Apply the sealer.

•

Apply the sealer to the matching surfaces of the

web plate, back panel lower, rear combination
lamp area and side panel outer.

9. Apply the undercoat.

•

Undercoat to the rear wheelhouse and designated

rear floor.

10.Apply the paint.

CAUTION

•

Ventilate when spraying paint. Most paint contains

substances that are harmful if inhaled or swal-
lowed.

Read the paint label before opening paint con-

tainer.

•

Avoid contact with skin. Wear an approved res-

pirator, gloves, eye protection and appropriate
clothing when painting.

•

Paint is flammable. Store in a safe place, and

keep it away from sparks, flames or cigarettes.

11.Coating the anti-rust agents.

•

Coating the anti-rust agents to the inside of frame

door opening areas sufficiently.

12.Apply the deadner.

•

Apply the deadner to the inside of side panel outer

center.(Left side only)

Содержание TACUMA































































































































Результаты поиска

Содержание TACUMA

Отзывы:

Похожие инструкции для TACUMA

Бренды по названию

Популярные бренды

Daewoo TACUMA, Руководство по ремонту кузова

Результаты поиска

Содержание TACUMA

Отзывы:

Похожие инструкции для TACUMA

Бренды по названию

Популярные бренды