Daewoo TACUMA Скачать руководство пользователя страница 42

Страница: 42 / 126

FRONT 4–11

3. FRONT LONGITUDINAL

3-1. GENERAL DESCRIPTION

The front longitudinal is joined to the wheelhouse and
front panel, it forms the base for the front suspension,
engine, transmission and others. Therefore, replace-
ment of the component affects the front wheel alignment
and maintains the rigidity of the front section. When
assembling it, either use a jig or follow dimensions on
the body repair chart for positioning. It must be welded
carefully.

3-2. REPAIR PROCEDURE

1. Remove the related parts.

•

Parts to be removed when removing the front panel

and front wheelhouse.

•

Parts on passenger side of dash panel lower which

are especially flammable.

•

Instrument panel, wiring harness, related parts and

others.

NOTE: Remove according to part damaged.

2. Roughly pull out and straighten the damaged area to

approximately the original shape.

•

Attach the car to the frame straightener by tight-

ening the underbody clamps at the horizontal pinch
weld points.

•

Before cutting off the damaged sections, pull them

out so that they are restored to the original shape.

•

Roughly cut off the front longitudinal according to

the extent of damage before roughly pulling out the
damage makes repair of the related parts difficult.

•

Do not pull out more than necessary.

NOTE: Check the condition of the door and hinges.

3. Peel off the undercoat and sealer.

•

Heat the undercoat and sealer at the welding ar-

eas of the damaged parts with a gas torch and
peel off the undercoat and sealer with a steel
spatula.

CAUTION: Be careful not to burn the fittings inside
the passenger compartment when heating.

4. Cut and pry off the front longitudinal.

NOTE: It's not necessary to separate the wheelhouse
from the front longitudinal if the wheelhouse is to be
replaced also.

•

Center punch around the spot weld imprints on the

wheelhouse and other related parts.

•

Use the special spot cutter to drill holes at the

spot weld nuggets on the center punched areas.

•

Cut off the front longitudinal with an air chisel, leav-

ing the welding flanges intact.

•

Level and finish the burrs from the pried off spot

welds with a disc sander.

CAUTION: To prevent eye injury, wear goggles or

safety glasses whenever sanding, cutting, or grind-
ing.

Fig. 17

5. Mold damaged related parts.

•

Fill any holes drilled by welding.

CAUTION: To prevent eye injury and burns when
welding, wear an approved welding helmet, gloves
and safety shoes.

•

Reshape the wheelhouse and other damaged

parts and even out the welding flanges with a
hammer and dolly.

Содержание TACUMA































































































































Результаты поиска

Содержание TACUMA

Отзывы:

Похожие инструкции для TACUMA

Бренды по названию

Популярные бренды

Daewoo TACUMA, Руководство по ремонту кузова

Результаты поиска

Содержание TACUMA

Отзывы:

Похожие инструкции для TACUMA

Бренды по названию

Популярные бренды