Daewoo TACUMA Скачать руководство пользователя страница 36

Страница: 36 / 126

FRONT 4–5

9. Finish the welding areas.

•

Use a hammer and dolly to even out the front

wheelhouse and longitudinal flanges for a close
fit with the surface of the front panel.

10.Apply the undercoat.

•

Undercoat to the damaged areas of front wheel-

house and longitudinal if necessary.

11.Apply the paint.

CAUTION

•

Ventilate when spraying paint. Most paint contains

substances that are harmful if inhaled or swal-
lowed.

Rear the paint label before opening paint con-

tainer.

•

Avoid contact with skin. Wear an approved res-

pirator, gloves, eye protection and appropriate
clothing when painting.

•

Paint is flammable. Store in a safe place, and

keep it away from sparks, flames or cigarettes.

Fig. 7

12.Coating the anti-rust agents.

•

Coating the anti-rust agents to the end of front

panel side and the door hinge areas.

13.Install the related parts.

•

Engine, radiator and related parts.

•

Aircon condenser and related parts.

•

Head lamps and fenders.

•

Hood, radiator grill, and bumper.

•

Others.

•

Install in the reverse order in which they were re-

moved.

NOTE: After install the all related parts, rub in grease
to the moving parts and replenish cooling liquid,
break oil, aircon gas and others.

14.Check and adjust

•

Check clearances and level differences.

•

Check the hood locking and unlocking condition.

•

Adjust the head lamp aim.

•

Check all operation.

•

Check for gas, oil and liquid leaks.

NOTE: Use specified check sheet for operation
check properly.

Fig. 8

Содержание TACUMA































































































































Результаты поиска

Содержание TACUMA

Отзывы:

Похожие инструкции для TACUMA

Бренды по названию

Популярные бренды

Daewoo TACUMA, Руководство по ремонту кузова

Результаты поиска

Содержание TACUMA

Отзывы:

Похожие инструкции для TACUMA

Бренды по названию

Популярные бренды