Daewoo TACUMA Скачать руководство пользователя страница 72

Страница: 72 / 126

6–4 FRAME DOOR OPENING, DOOR AND SIDE PANEL OUTER

•

Perform a trial welding first, and check the weld-

ing condition.

•

Increase the number of spot by 20% for areas to

be spot welded.

5. Set the new frame door opening.

•

Grind both sides of the welding section of the pre-

pared frame door opening part with a disk sander
to remove the paint and expose the steel plate.

•

Clamp the new panel in place with the vise grips.

•

Tack weld the clamped section for temporary in-

stallation.

CAUTION: To prevent eye injury and burns when
welding, wear an approved welding helmet, gloves
and safety shoes.

7. Finish the welding areas.

•

Level the gas or MIG welded areas with a disc

sander, then even out high areas with a hammer
being careful not to deform them.

CAUTION: To prevent eye injury, wear goggles or
safety glasses whenever sanding, cutting, or grind-
ing.

•

Use a hammer and dolly to even out the spot

welded flanges for a close fit with the surface of
the frame door opening panel.

•

Fill in deformations and level differences of the

welded areas with solder or putty, then finish.

8. Apply the sealer.

•

Apply the sealer to the matching surfaces of the

floor and frame door opening.

Fig. 4

•

Remove the vise grips and temporarily install the

fender and doors, then check the clearances, level
differences and outer appearance.

6. Perform the main welding.

•

Weld the front, rear frame door opening and cen-

ter pillar at the butt joints with a gas or MIG
welder.

•

Spot weld the frame door opening and center

pillar as shown.

CAUTION: To prevent eye injury and burns when
welding, wear an approved welding helmet, gloves
and safety shoes.

Fig. 5

Содержание TACUMA































































































































Результаты поиска

Содержание TACUMA

Отзывы:

Похожие инструкции для TACUMA

Бренды по названию

Популярные бренды

Daewoo TACUMA, Руководство по ремонту кузова

Результаты поиска

Содержание TACUMA

Отзывы:

Похожие инструкции для TACUMA

Бренды по названию

Популярные бренды