Daewoo TACUMA Скачать руководство пользователя страница 41

Страница: 41 / 126

4–10 FRONT

13.Apply the sealer

•

Apply the sealer to the matching and overlapped

surface.

14.Apply the undercoat.

•

Undercoat to the inside of the front, rear wheel-

house and longitudinal.

15.Apply the paint.

CAUTION

•

Ventilate when spraying paint. Most paint contains

substances that are harmful if inhaled or swal-
lowed.

Read the paint label before opening paint con-

tainer.

•

Avoid contact with skin. Wear an approved res-

pirator, gloves, eye protection and appropriate
clothing when panting.

•

Paint is flammable. Store in a safe place, and

keep it away from sparks, flames or cigarettes.

16.Coating the anti-rust agents.

•

Coating the anti-rust agents to the end of front

panel side and the door hinge areas.

17.Install the related parts.

•

Wiring harness, instrument panel and related

parts.

•

Parts of the passenger compartment.

•

Parts to be installed when install the front panel.

•

Others.

•

Install in the reverse order in which they were re-

moved.

NOTE: After install the all related parts, rub in grease
to the moving parts and replenish cooling liquid,
break oil, aircon gas and others.

18.Check and adjust

•

Measure the front wheel alignment.

•

Check clearances and level differences.

•

Check the hood locking and unlocking condition.

•

Adjust the head lamp aim.

•

Check all operation.

•

Check for gas, oil and liquid leaks.

NOTE: Use specified check sheet for operation check
properly.

Содержание TACUMA































































































































Результаты поиска

Содержание TACUMA

Отзывы:

Похожие инструкции для TACUMA

Бренды по названию

Популярные бренды

Daewoo TACUMA, Руководство по ремонту кузова

Результаты поиска

Содержание TACUMA

Отзывы:

Похожие инструкции для TACUMA

Бренды по названию

Популярные бренды