2-48
SS41-W00
May. 2007
LK30
CLUTCHCLUTCHCLUTCHCLUTCHCLUTCH
ENGINEENGINEENGINEENGINEENGINE
TRANSMISSIONTRANSMISSIONTRANSMISSIONTRANSMISSIONTRANSMISSION
FRONT AXLEFRONT AXLEFRONT AXLEFRONT AXLEFRONT AXLE
STEERINGSTEERINGSTEERINGSTEERINGSTEERING
BARKEBARKEBARKEBARKEBARKE
ELECTRICELECTRICELECTRICELECTRICELECTRIC
INDEXINDEXINDEXINDEXINDEX
HYDRAULICHYDRAULICHYDRAULICHYDRAULICHYDRAULIC
GENERALGENERALGENERALGENERALGENERAL
REAR AXLEREAR AXLEREAR AXLEREAR AXLEREAR AXLE
C. REMOVING NOZZLE HOLDER ASSEMBLIES
1. Remove the pipe clips holding the fuel overflow
pipes, and detach the pipes.
2. Detach the nozzle holders using a 27 mm (1.0630
in.) nozzle holder socket wrench, after loosening
the lock nuts.
3. Detach the copper gaskets on the seats on which
the nozzles are to be installed.
(Note for reassembling)
•
Return the nozzle holders after confirming that there
are no metallic particles or foreign matter on the
surface on which the nozzles are to be installed.
(1) Nozzle holder socket wrench
(2) Lock nut
196W257B
Item
Nozzle Holder Assem-
bly
Tightening torque
49.0 ~ 68.6 Nm
5.0 ~ 7.0 kgf-m
36.1 ~ 50.6 lb-ft
(1) Philips screwdriver
(2) Nozzle
(3) Injection nozzle gasket
(4) Heat seal
196W258B
D. HEAT SEAL ROMOVAL PROCEDURE
1. Drive the Philips screwdriver lightly into the heat
seal hole.
2. Turn screw driver three or four times each way.
3. While turning the screw driver, slowly pull the heat
seal up together with the injection nozzle gasket. If
the heat seal drops, repeat the above procedure.
4. Heat seal and injection nozzle gasket must be
changed when the injection nozzle is removed for
cleaning or for service.
NOTE:
•
Use a philips screwdriver that has a diameter which
is bigger than the heat seal hole 1/4 in (approx. 6 mm)
(1) Injection pipe 1
(3) Injection pipe 3
(2) Injection pipe 2
196W256B
B. REMOVING INJECTION PIPES 1, 2 AND 3
1. Loosen the screws on the pipe clamps.
2. Detach the injection pipes in the order of 1, 2 and 3.
(Note for reassembling)
•
Send compressed air, into the pipes to blow out
dust. Then reassemble the pipes in the reverse
order.
Item
Injecion pipe nuts
Tightening torque
24.5 ~ 34.3 Nm
2.5 ~ 3.5 kgf-m
18.1 ~ 25.3 lb-ft
•
Pipe clamp
•
Feed pipe (17 mm)
•
Injection pipe
ENGINE - SERVICING
Lk30_02_engine(41-82).p65
2007-07-26, ¿ÀÈÄ 12:04
Page 48
Adobe PageMaker 6.5K/Win
Содержание Kioti LK30
