background image

 

ENGLISH 

 

15 

 

All technical data are marked on the technical label on the pump. 

The various items are explained below (Fig. 4): 

 

Fig.4 Data plate 

 

 

Pos. 

Description 

Description 

Revision 

Year 

Week 

Serial number 

Maximum liquid temperature 

Use 

Flow rate 

Maximum head 

10 

Minimum head 

11 

Insulation class 

12 

Degree of protection 

13 

Submersibility 

14 

Rated voltage 

15 

Ampere 

16 

P1 

17 

P2 HP 

18 

P2 kW 

19 

Frequency 

20 

Condenser capacity 

21 

Voltage 

22 

Rated number of revolutions 

23 

Logos 

24 

Pump code 

 

2

 

INSTALLATION 

Before starting up the pump, check that: 

 

 

The voltage and frequency on the pump’s technical data plate correspond to the values of the power supply system. 

The pump's power cable or the pump is not damaged. 

The electrical connection must be made in a dry place, far from any possible flooding. 

The electrical system is provided with a residual-

current circuit breaker with I ∆n ≤ 30 mA and that the earth system is efficient.

 

Any extension cables comply with the regulations in force. 

 

2.1

 

Mechanical Installation 

 

 

Install the pump in a location that is not exposed to freezing.  

When the pump remains inactive at a temperature lower than 0°C, it is necessary to ensure that there is no water residue which 

could freeze and damage it. 

 

Hang the pump by passing the rope through the hole provided (see figure 5). Do not hang the pump by the handle. 

 

Do not install check valves near the pump delivery (distance less than 1 metre (3.28ft)). The pump already has a built-in check 

valve on delivery. 

 

The DTRON3 pumps already contain a small expansion tank, calibrated for water hammer and small leaks. 

In order to reduce the number of pump starts, an auxiliary tank (Figure 6, A) with a capacity of 2 litres can be installed.  

If you want to install an additional non return valve (Figure 6, B), it is recommended to position it downstream from the auxiliary tank. 

 

Do not subject the motor to excessive starts per hour. It is strictly recommended not to exceed 60 starts per hour. 

 

Содержание DTron 3















Отзывы: