background image

 

ENGLISH 

 

21 

 

8.2

 

Description of LEDs / buttons 

 

See Figure 12 

LED 

Function 

Explanation 

 

CUT-IN 

The lit LED indicates the CUT-IN value 

12 

 

 

 

ON/OFF 

System status: on or off 

 

 

 

MOTOR STATUS 

Indicates whether or not the pump is operating 

 

 

 

ALARM 

Indicates that there is a general alarm 

 

 

 

MANUAL MODE 

Indicates manual operation 

 

 

 

 

PLC 

Indicates correct communication between pump and COM 

BOX 

11 

 

 

 

ANTI DRYRUN 

Indicates that there is a DRY RUN alarm 

10 

 

 

 

ANTI-CYCLING 

Indicates that there is an ANTICYCLING alarm and/or that 

the ANTICYCLING activated status has been detected 

1 - 2 

+ / - 

 

RESET/SELECT 

 

Table2 

 

9

 

INTERFACE OPERATIVITY 

9.1

 

Passage from Monitor to SETUP mode and vice-versa 

To pass

 from Monitor mode to SETUP mode

, hold down the buttons “+” (Figure 12, 1) and “Reset/Select” (Figure 12, 3) simultaneously for at 

least 3 seconds. To pass 

from SETUP mode to Monitor mode

, hold down the buttons “–“ (Figure 12, 2) and ”Reset/Select” (Figure 12, 3) 

simultaneously for at least 3 seconds or wait for 1 minute without touching any button on the interface. When switched on, the COM BOX is in 

Monitor mode by default. 

 

9.2

 

Monitor mode 

Motor status (Fig 12, 4) 

If the green “Motor Status” LED is lit, the motor is powered. 

 

Alarm reading (Fig 12, 5) 

If the “Alarm” LED is lit, it indicates that an alarm has been activated. The lighting of the ANTICYCLING or DRYRUN LED indicates which alarm 

is active.  

 

MANUAL MODE function (fig.12, 7)  

The active “MANUAL” mode is indicated by the lit LED. To activate/deactivate this mode, see the chapter “SETUP Mode”. 

 

PLC connection (Fig 12, 8) 

If the LED is lit, the PLC connection is active or the COM BOX is available for connection to a pump.  

If the LED is lit with a steady light, the connection is active. 

If the LED is flashing slowly (1 second ON; 1 second OFF) it indicates that the connection is not active, but COM BOX is associated with the 

pump. 

If the LED is flashing rapidly (0.5 seconds ON; 0.5 seconds OFF), it indicates that COM BOX and DTRON3 are associating. 

Содержание DTron 3















Отзывы: