CYBEX CardioTouch 770T Скачать руководство пользователя страница 70

Страница: 70 / 261

• GFX On Time
• Days in Service
• Backlight On Time
• iPod Attaches
• iPod On Time
• Touch Panel Usage (total)

Install Icon

– This icon is active to allow resetting the install date for the GUI

Module.

LCD

Days in Service

Stop

– How many times the membrane’s stop button was pressed and released.

Ch Up

– How many times the Channel Up button was pressed and released.

Speed Up

– How many times the Speed Up button was pressed and released.

Incline Up

– How many times the Incline Up button was pressed and released.

Fan

– How many times the fan button was pressed and released.

Install Icon

– This icon is active to allow resetting the install date for the

membrane.

Membrane

• OSD On Time
• Days in Service
• Backlight On Time
• Max Temp
• Current Temp

Install Icon

– This icon is active to allow resetting the install date for the

membrane.

PEM Statistics

Shows the number of times each workout was started.

Program Usage

Days in Service

– Today’s date minus the Install Date.

Session Time

– Average session time in minutes.

Session Speed

– Average session speed.

Power Draw

– Average power draw.

Daily Starts

– Average number of starts per day.

Daily Distance

– Average distance covered in a day.

Install Icon

– This icon is active to reset the displayed averages only, showing

the date it was last reset in the text window.

Statistics

Page 70 of 261

Cybex 770T/790T Treadmill Part Number

Содержание CardioTouch 770T






































































































































































































































































Результаты поиска

Содержание CardioTouch 770T

Отзывы:

Бренды по названию

Популярные бренды

CYBEX CardioTouch 770T, Руководство по обслуживанию

Результаты поиска

Содержание CardioTouch 770T

Отзывы:

Бренды по названию

Популярные бренды