CYBEX CardioTouch 770T Скачать руководство пользователя страница 217

Страница: 217 / 261

Remove wireless heart rate board

The wireless heart rate board is installed with double sided tape. Remove only if replacing with a new
wireless heart rate board.

Unplug the wireless heart rate cable by un-latching connector from the wireless heart rate board.

Qty.

Description

Item

Wireless Heart Rate Cable

Wireless Heart Rate Board

Pry the wireless heart rate board from the console using a flat head screwdriver.

Clean any remaining double sided tape from the console.

Install wireless heart rate board

Locate the new wireless heart rate board.

Peel the backing from the double sided tape and place the wireless heart rate board in position on
the console.

Qty.

Description

Item

Wireless Heart Rate Cable

Wireless Heart Rate Board

Plug the wireless heart rate cable into the wireless heart rate board.

Install back cover

Install the four screws securing the back cover to the console assembly using a Phillips screwdriver.

Page 217 of 261

Cybex 770T/790T Treadmill Part Number

Содержание CardioTouch 770T






































































































































































































































































Результаты поиска

Содержание CardioTouch 770T

Отзывы:

Бренды по названию

Популярные бренды

CYBEX CardioTouch 770T, Руководство по обслуживанию

Результаты поиска

Содержание CardioTouch 770T

Отзывы:

Бренды по названию

Популярные бренды