CYBEX CardioTouch 770T Скачать руководство пользователя страница 129 | Manualshive

Страница: 129 / 261

background image

Install end caps

1.

Install two screws securing right end cap using a Phillips screwdriver.

Qty.

Description

Item

2

Screws

1

1

Right end cap

2

2.

Repeat step for left end cap.

Center and tension the running belt

1.

Plug the power cord into the power outlet.

2.

Turn the main power switch to the on (I) position.

3.

Tap the

Quick Start

icon.

4.

Press the

Speed +

key to bring the speed up to 5 mph (8 kph). Allow the treadmill to run for a minute.

The lateral position of the running belt is correctly centered when the Cybex logo is centered between
the inside edges of the two belt tracking slots. If the Cybex logo is not centered between the belt
tracking slots, center the running belt with the following procedure.

5.

Observe the Cybex logo position relative to the belt tracking slots with the treadmill running at 5 mph
(8 kph).

Qty.

Description

Item

1

Cybex logo

1

1

Running belt

2

4

Belt tracking slot

3

While centering the running belt choose one bolt to adjust. Do not adjust both bolts.

Page 129 of 261

Cybex 770T/790T Treadmill Part Number

«
...
127
128
129
130
131
...
»

Содержание CardioTouch 770T






































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CardioTouch 770T

Бренд: Hagie Страницы: 61

Бренд: JackJaw Страницы: 2

Бренд: Raytheon Страницы: 69

Бренд: Galaxy Audio Страницы: 24

Бренд: AccuMed Страницы: 14

Бренд: TAS Страницы: 25

Бренд: B-K lighting Страницы: 3

Бренд: Nautilus Страницы: 12

Бренд: CAIRE Страницы: 16

Бренд: NCR Страницы: 20

Бренд: DARAY Страницы: 32

Body Armor Night Splint

Бренд: Darco Страницы: 2

Бренд: MacDon Страницы: 74

Бренд: h/p/cosmos Страницы: 81

Бренд: IBEX Страницы: 4

DISHSTAR ADA-SEER

Бренд: Jackson Страницы: 2

Бренд: JB-Lighting Страницы: 32

Бренд: W&H Страницы: 72

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды