CYBEX CardioTouch 770T Скачать руководство пользователя | Manualshive

Страница: 192 / 261

background image

Incline Motor

Tools Required:

• Phillips screwdriver
• Block, 4" (10 cm) (2)
• 9/16” Open end wrench
• 9/16” Socket wrench
• Tape measure

Disconnect power source

1.

Toggle the on/off (I/O) power switch to the off (O) position. The on/off (I/O) power switch is located
under the front end of the unit, or on the front right side panel.

2.

Unplug the treadmill from the power outlet.

Shock and electrocution hazard.
• Unplug unit and let sit 10 minutes before cleaning or performing

maintenance.

• Electrical charge can remain in unit after unplugging.
• Keep water and liquids away from electrical parts.

Place blocks under frame

Heavy equipment.
• At least two people must lift, move or assemble unit.
• Use safe lifting methods.

Lift the front of the treadmill with two people, have a third person place a 4" (10 cm ) block under each
side of the frame to support the front end of the treadmill. This will get the weight of the treadmill off the
elevation wheels and provide support.

Remove motor cover

1.

Loosen, but do not remove the two front cover screws securing the motor cover using a Phillips
screwdriver.

Qty.

Description

Item

1

Motor Cover

1

1

Front Cover

2

2

Screws

3

4

Plastic Connectors

4

Page 192 of 261

Cybex 770T/790T Treadmill Part Number

«
...
190
191
192
193
194
...
»

Содержание CardioTouch 770T






































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CardioTouch 770T

Бренд: Jackco Страницы: 6

Aspect Q-CARD 100-4T

Бренд: idi Страницы: 38

Бренд: Konica Minolta Страницы: 32

FUSION APOLLO MS-WB675

Бренд: Garmin Страницы: 18

Бренд: Rapid Shape Страницы: 12

MultiFill 003-561-005

Бренд: Hanskamp Страницы: 20

Бренд: Walimex Pro Страницы: 44

Бренд: Otto Bock Страницы: 72

Бренд: Opvimus Страницы: 50

Бренд: ABB Страницы: 112

DependaBar DB-18-PCW

Бренд: Healthcraft Страницы: 13

Бренд: Garmat Страницы: 13

Бренд: Gama Sonic Страницы: 4

Бренд: Ametek Страницы: 20

L10 LVELED Series

Бренд: Clevetronics Страницы: 2

Бренд: Goobay Страницы: 20

Бренд: EHEIM classic Страницы: 128

MINOR 2000 G.E.

Бренд: Oscartielle Страницы: 44

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды