CYBEX CardioTouch 770T Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 261

CYBEX CardioTouch 770T Скачать руководство пользователя страница 10

Emergency Stop Key (e-stop)

The e-stop key functions as an emergency stop. In an emergency situation, the e-stop key disengages
from the console and the treadmill will come to a stop. Before using the treadmill, clip the e-stop key as
described below.

1.

Compress the spring and clip the e-stop clamp to your clothing.
Ensure the clip engages enough clothing so it does not fall off in an emergency situation. Be sure
the string is free of knots and has enough slack for you to workout comfortably with the e-stop key
in place.

Qty.

Description

Item

1

Clothing

1

1

Clip

2

2.

Without falling off the treadmill, carefully step backward until the e-stop pulls out of the console.
If the e-stop clip falls off your clothing then the test has failed. Reclip the e-stop clip to your clothing
and repeat this step.

3.

Replace the e-stop key.

4.

The treadmill is now ready to be used. Ensure the e-stop clip is secured to your clothing at all times
during use.

Page 10 of 261

Cybex 770T/790T Treadmill Part Number

«
...
8
9
10
11
12
...
»

Содержание CardioTouch 770T






































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды