CYBEX CardioTouch 770T Скачать руководство пользователя страница 181

Страница: 181 / 261

Remove power cord

Remove the mounting screw securing the mounting bracket in place using a Phillips screwdriver.

Qty.

Description

Item

Power Cord

Power Cord Inlet

Mounting Bracket

Mounting Screw

Unplug the power cord from the power cord inlet.
Power cord may be routed through frame. See Owner’s manual.

Install power cord

Plug the power cord into the power cord inlet.

Qty.

Description

Item

Power Cord

Power Cord Inlet

Mounting Bracket

Mounting Screw

Install the power cord with the mounting screw and mounting bracket using a Phillips screwdriver.

Complete installation

Plug the power cord into the power outlet.

Verify the power cord is not being pinched under the front of the treadmill.

Operate the unit at all levels to verify proper operation.

On/Off Switch

Tools Required:

• Phillips screwdriver
• Flat head screwdriver

Disconnect power source

Toggle the on/off (I/O) power switch to the off (O) position. The on/off (I/O) power switch is located
under the front end of the unit, or on the front right side panel.

Page 181 of 261

Cybex 770T/790T Treadmill Part Number

Содержание CardioTouch 770T






































































































































































































































































Результаты поиска

Содержание CardioTouch 770T

Отзывы:

Похожие инструкции для CardioTouch 770T

Бренды по названию

Популярные бренды

CYBEX CardioTouch 770T, Руководство по обслуживанию

Результаты поиска

Содержание CardioTouch 770T

Отзывы:

Похожие инструкции для CardioTouch 770T

Бренды по названию

Популярные бренды