CYBEX CardioTouch 770T Скачать руководство пользователя страница 239

Страница: 239 / 261

Complete installation

Plug the power cord into the power outlet.

Verify the power cord is not being pinched under the front of the treadmill.

Operate the unit at all levels to verify proper operation.

Contact Heart Rate Grips

Tools Required:

• Phillips screwdriver
• Needle nose pliers
• ESD (Electrostatic Discharge) grounding strap

Disconnect power source

Unplug the power cord from the power outlet.

Shock and electrocution hazard.
• Unplug unit and let sit 10 minutes before cleaning or performing

maintenance.

• Electrical charge can remain in unit after unplugging.
• Keep water and liquids away from electrical parts.

Remove handset assembly

Remove eight screws securing handset to console using a Phillips screwdriver.

Qty.

Description

Item

Handset assembly

Console

Screw

Repairs and Service. Do not damage the wires or connectors when
installing or removing cables.

Use flashlight to locate cable connectors.

Page 239 of 261

Cybex 770T/790T Treadmill Part Number

Содержание CardioTouch 770T






































































































































































































































































Результаты поиска

Содержание CardioTouch 770T

Отзывы:

Похожие инструкции для CardioTouch 770T

Бренды по названию

Популярные бренды

CYBEX CardioTouch 770T, Руководство по обслуживанию

Результаты поиска

Содержание CardioTouch 770T

Отзывы:

Похожие инструкции для CardioTouch 770T

Бренды по названию

Популярные бренды