CYBEX CardioTouch 770T Скачать руководство пользователя страница 22

Страница: 22 / 261

Customer Service

Product Registration

To register product do the following:.

Visit

www.cybexintl.com

Locate Product Registration in the Support section.

Fill out form completely.

Click the

Submit

button to register product.

Contacting Service

Hours of phone service are Monday through Friday from 8:30 a.m. to 6:00 p.m. Eastern Standard Time.

For Cybex customers living in the USA, contact Cybex Customer Service at 1-888-462-9239.

For Cybex customers living outside the USA, contact Cybex Customer Service at 1-508-533-4300 or
fax 1-508-533-5183. Email address

[email protected]

Find information on the web at

www.cybexintl.com

To contact us online go to

www.cybexintl.com

Ordering Parts

To order parts online go to

www.cybexintl.com

To speak with a customer service representative, call 800-351-3737 (for customers living within the
USA) or 847-288-3700 (for customers outside the USA).

The following information located on the serial number decal will assist our Cybex representatives in
serving you.

• Unit Serial Number, Product Name and Model Number
• Part Description and Part Number if you have it. All parts can be found on the web at

www.cybexintl.com

• Shipping Address
• Contact Name
• Include a description of the problem.

In addition to your shipping address and contact name, your account number is helpful but not required.
You may also fax orders to 800-216-8893.

Page 22 of 261

Cybex 770T/790T Treadmill Part Number

Содержание CardioTouch 770T






































































































































































































































































Результаты поиска

Содержание CardioTouch 770T

Отзывы:

Бренды по названию

Популярные бренды

CYBEX CardioTouch 770T, Руководство по обслуживанию

Результаты поиска

Содержание CardioTouch 770T

Отзывы:

Бренды по названию

Популярные бренды