CYBEX CardioTouch 770T Скачать руководство пользователя

Страница: 58 / 261

Tap

to adjust settings.

Settings

Feature

Select Off or Last. Last will set caption mode to last used setting.

Power on Captions Mode

(ATSC only)

Select Off or Last. Last will set subtitle mode to last used setting.

Power on Subtitles Mode

(DVB-T only)

Set current time automatically from digital signal. Select time zone and
daylight savings time to Auto, On, or Off.

Digital Mode Time Setup

Provides diagnostic information only. Settings cannot be changed.

Diagnostics

Select Enabled or Disabled.

Caption Text Modes

(ATSC only)

Tap the

Setup

icon to return to

SETUP MODE

menu.

OSD Language

Tap

to select

OSD Language

Tap

to select language.

Description

Option

English, Français or Español.

ATSC choices

English, Français, Español, Dutch, Danish, Russian, German, and Swedish.

DVB-T choices

Tap the

Setup

icon to return to

SETUP MODE

menu.

Exit Set Up Mode by tapping the

Toolbox

icon, then tap the

Home

icon

. The screen will

refresh.

Setup Complete

Cybex GO Setup

Prerequisites:

• Coax cable with TV signal
• Netpulse Gateway installed and running, providing the connection via:

•

Wired (Ethernet) –

Ethernet cable is connected to the Cybex equipment through a network switch

to the Gateway

•

Wireless –

Gateway has been installed in the facility using a unique wireless access point. Cybex

GO Monitor will not connect to any other routers in the area.

• Power to the Cybex Equipment.

Page 58 of 261

Cybex 770T/790T Treadmill Part Number

Содержание CardioTouch 770T






































































































































































































































































Результаты поиска

Содержание CardioTouch 770T

Отзывы:

Похожие инструкции для CardioTouch 770T

Бренды по названию

Популярные бренды

CYBEX CardioTouch 770T, Руководство по обслуживанию

Результаты поиска

Содержание CardioTouch 770T

Отзывы:

Похожие инструкции для CardioTouch 770T

Бренды по названию

Популярные бренды