Cybex Silver PALLAS B-FIX, Руководство пользователя

Страница: 8 / 144

6
EN
PRODUCT PARTS
(a) User Guide Storage Compartment
(b)
Backrest
(c) Adjustable Headrest
(d) Headrest Height Adjuster
(e) Booster
(f) Impact Shield
(g) Belt Guide Group 1
(h) Lap Belt Guide Group 2/3
(i) Shoulder Belt Guide
(j) Side Impact Protection
(k) Latch-Connect-Hooks
(l) Latch-Adjuster
(m) ISOFIX-Anchorage-Points
INITIAL ASSEMBLY
Connect the backrest (b) to the booster (e) by hooking the guide lug on the
axis of the booster. The backrest (b) is then folded forward. Place the impact
shield (f) on the booster (e) .
THE CORRECT POSITION IN THE VEHICLE
The child seat with stored latch-connect-system can be used on all vehicle
seats with automatic three-point safety belts approved in the vehicle manual
for “universal” use.
A “semi-universal” certification is given to restraint systems that are connected
to the car through the latch-connect-system. For this reason, the latch-connect-
system can only be used in certain vehicles. Please refer to the enclosed
vehicle type list for approved vehicles. You can obtain the most up-to-date
version from www.cybex-online.com . Above a child’s stature of 135 cm, the
compatibility between the Pallas B-Fix and your vehicle might be reduced.
Please review the vehicle type list to check whether the child seat can be used
in all headrest positions without restrictions.
In exceptional cases, the child car seat may also be used on the front
passenger seat. Always comply with the recommendations of the vehicle
manufacturer.
INSTALLING THE CHILD SEAT IN THE VEHICLE
1. Always ensure that…
•the backrests in the vehicle are locked in their upright position.
•when installing the child seat on the front passenger seat, adjust the vehicle
seat as far back as possible without affecting the belt routing.
2. Elongate the straps of the latch-connect-system by using the latch-adjuster (l) .
3. Attach the latch-connect-hooks (k) to the ISOFIX-anchorage-points (m) .
4. Tighten the latch-connect-system by pulling the strap on the adjuster until
the position of the child seat is adjusted correctly.
5. Ensure that the entire surface of the backrest of the child seat (b) is placed
against the backrest of the vehicle seat.
💡
If the headrest of the vehicle is in the way, pull it upwards to its furthest
extent or remove it completely (except rear-facing vehicle seats).
6. Ensure the seat is secure by trying to pull it out of the
ISOFIX-anchorage-points (m) .
7. In case the seat is used without latch-connect-system, it can be stored away
on the bottom of the seat.
💡
Using the latch-connect-system, you can fix the
CYBEX Pallas B-fix to the vehicle, thereby increasing your child’s safety.
The child still needs to be secured with the three-point belt of your vehicle
and the impact shield for Group 1.
REMOVING THE CHILD SEAT FROM THE VEHICLE
Perform the installation steps in the reverse order.
1. Release the tightened straps using the latch-adjuster
(l) .
2. Disconnect the latch-connect-hooks (k) on both sides.
3. Remove the child seat.
4. You can store the latch-connect-system in the booster of the child seat.
ADJUSTING THE HEADREST
The headrest (c) can be adjusted by using the headrest height adjuster (d)
at the back of the headrest (c) . Adjust the headrest so that max. 2 cm (approx.
2 finger’s width) remain between the child’s shoulder and the headrest (c) .
💡
The height of the headrest can still be adjusted while the seat is installed
in the car.