CURRENT Luxury SilenTrac Скачать руководство пользователя страница 20

Страница: 20 / 25

Using the Drapery Track

Using the Pendant for Operation

The Pendant, can be pulled down or pushed up, depending on the desired movement.

On a single drapery

, pulling the Pendant down activates the curtain. Pulling down once makes the curtain move towards the

next position, depending on if the curtain is open or closed. Pushing the Pendant up will stop it. Pulling down a second time after

stopping will allow the curtain to move in the opposite direction.

On a dual drapery

, pulling the Pendant down activates the curtain plugged into the motor 1 slot. Pulling down once makes the

curtain move towards the next position, depending on if the curtain is open or closed. Pulling down a second time will stop it.

Pulling down a third time will move the curtain in the opposite direction.

Lifting up on the Pendant will activate the curtain plugged into the motor 2 slot. Lifting up once makes the curtain move towards

the next position, depending on if the drapery is open or closed. Lifting up a second time will stop it. Lifting up a third time will

move the curtain in the opposite direction.

Using Smart Assist

Smart Assist is a drapery track feature to allow users the ability to begin an open or close movement manually, and have the

drapery automatically complete the movement.

To trigger Smart Assist, simply pull the curtain approximately one foot towards the direction you would like to move the curtain.

Upon release, the curtain will continue moving in that direction until it reaches the full open or closed position.

Содержание SilenTrac


























Результаты поиска

Содержание SilenTrac

Отзывы:

Похожие инструкции для SilenTrac

Бренды по названию

Популярные бренды

CURRENT Luxury SilenTrac, Руководство по установке

Результаты поиска

Содержание SilenTrac

Отзывы:

Похожие инструкции для SilenTrac

Бренды по названию

Популярные бренды