CSZ Norm-O-Temp 111W Скачать руководство пользователя страница 61

Страница: 61 / 82

Operation / Technical Manual

NORM-O-TEMP

, Model 111W

Page 61 of 82

Membrane control panel

Remove the top of the unit as described in Section 6-1.1.

Position the top of the unit face down on a padded work space.

Using a 5/16 inch wrench, remove the six nuts and star washers on the

edge of the board

Slide off the clear strip cable on the left side of the microprocessor board.

Remove the microprocessor board.

Carefully place the microprocessor board aside. If only the microprocessor

board is to be replaced, go to step K.

To replace the membrane control panel, use a ¼ inch wrench to remove the

six stand-offs and put aside. The control panel is released and falls

outward. Put the control panel aside.

Position the replacement control panel from the face side of the top

assembly so that the screw posts align with the holes, the writing on the

control panel is right side up, and the clear strip connector is on the right

side.

Insert and tighten the six stand-offs

Position the new microprocessor board on the six stand offs so that the LED

display will be face down and the clear strip connector connects to the left

side.

Connect the cable to the 7-pin connector.

Insert and tighten the six nuts and star washers on the edge of the board

and tighten using a 5/16 inch wrench.

Secure the top of the unit as described in Section 6-1.2.

6-17.

Electrical Safety

The NORM-O-TEMP

unit should be checked quarterly for electrical safety. It is

appropriate to perform such inspection upon receipt of a new unit prior to acceptance,

and then again during each periodic inspection.

Содержание Norm-O-Temp 111W



















































































Результаты поиска

Содержание Norm-O-Temp 111W

Отзывы:

Похожие инструкции для Norm-O-Temp 111W

Бренды по названию

Популярные бренды

CSZ Norm-O-Temp 111W, Руководство по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание Norm-O-Temp 111W

Отзывы:

Похожие инструкции для Norm-O-Temp 111W

Бренды по названию

Популярные бренды