CSZ Norm-O-Temp 111W Скачать руководство пользователя страница 81

Страница: 81 / 82

Operation / Technical Manual

NORM-O-TEMP

, Model 111W

Page 81 of 82

Recommended separation distances between portable and mobile RF communications equipment and

the NORM-O-TEMP

, Model 111W

The NORM-O-TEMP

, Model 111W is intended for use in an electromagnetic environment in which radiated RF disturbances are controlled.

The customer or the user of the NORM-O-TEMP

, Model 111W can help prevent electromagnetic interference by maintaining a minimum

distance between portable and mobile RF communications equipment (transmitters) and the NORM-O-TEMP

, Model 111W as

recommended below, according to the maximum output power of the communications equipment.

Rated maximum output

power of transmitter

Separation distance according to frequency of transmitter

150 kHz to 80 MHz

d = 1,2√P

80 MHz to 800 MHz

d = 1,2√P

800 MHz to 2,5 GHz

d = 2,3√P

0,01

0,12

0,23

0,1

0,38

0,73

1,2

2,3

3,8

7,3

100

For transmitters rated at a maximum output power not listed above, the recommended separation distance

in meters (m) can be estimated

using the equation applicable to the frequency of the transmitter, where

is the maximum output power rating of the transmitter in watts

(W) according to the transmitter manufacturer.

Note 1: At 80 MHz and 800 MHz, the separation distance for the higher frequency range applies.

Note 2: These guidelines may not apply in all situations. Electromagnetic propagation is affected by absorption and reflection from

structures, objects and people.

NORM-O-TEMP

, MAXI-THERM

LITE, Gelli-Roll

and PLASTI-PAD

are

registered trademarks of Cincinnati Sub-Zero Products, LLC, Cincinnati, Ohio USA.

Содержание Norm-O-Temp 111W



















































































Результаты поиска

Содержание Norm-O-Temp 111W

Отзывы:

Похожие инструкции для Norm-O-Temp 111W

Бренды по названию

Популярные бренды

CSZ Norm-O-Temp 111W, Руководство по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание Norm-O-Temp 111W

Отзывы:

Похожие инструкции для Norm-O-Temp 111W

Бренды по названию

Популярные бренды