CSZ Norm-O-Temp 111W Скачать руководство пользователя страница 29

Страница: 29 / 82

Operation / Technical Manual

NORM-O-TEMP

, Model 111W

Page 29 of 82

Visually inspect the NORM-O-TEMP

unit to determine that there are no missing

parts, dents, or punctures.

Examine the power cord for cuts or exposed wires and the power plug for bent

or missing prongs.

Review Section 1-3 to identify the features of the NORM-O-TEMP

unit.

Collect and arrange the following equipment and supplies:

Hyper-hypothermia blanket/pad(s) Listed in Figure 8.

Connecting hose with quick-disconnect Hansen fittings (if applicable).

Mount the NORM-O-TEMP

unit on the proper stand.

To mount the NORM-O-TEMP

on IV Pole Stand:

Place the NORM-O-TEMP

on the equipment pan with the rear of the

unit facing the IV pole. Slide the NORM-O-TEMP

toward the IV pole

until the rubber bumper touches the pole

ii.

Fasten the NORM-O-TEMP

by turning the knurled knobs (on the

underside of the equipment pan) clockwise into the threaded holes on
the bottom of the NORM-O-TEMP

. Hand tighten knurled knobs until

snug.

iii.

Fasten the mounting bracket around the lower IV pole near the

bumper on the rear of the NORM-O-TEMP

with the two stainless

steel machine screws provided.

To mount the NORM-O-TEMP

on the Low Profile Stand:

Place the NORM-O-TEMP

unit on the equipment pan so that the

threaded holes on the bottom of the unit line up with the knurled
knobs (on the underside of the equipment pan).

ii.

Fasten the NORM-O-TEMP

by turning the knurled knobs clockwise

into the threaded holes on the bottom of the NORM-O-TEMP

. Hand

tighten knurled knobs until snug.

Slide the lid of the water fill opening and add 340 cc of propylene glycol then

gradually pour approximately 6 quarts (5.7 liters) of distilled water into the

reservoir. DO NOT USE DE-IONIZED WATER OR TAP WATER. Stop pouring

when the water reaches the strainer visible at the bottom of the water fill
opening. DO NOT OVERFILL.

Connect the blanket/pad(s) to the NORM-O-TEMP

unit by attaching the quick-

disconnect female Hansen socket of the connecting hose to a male outlet Hansen
plug (on the bottom row) of the unit. Attach the male quick-disconnect Hansen

plug of the connecting hose to a female return Hansen socket (on the top row) of

the unit. Each blanket/pad must be connected to one outlet coupling and one

return coupling of the connecting hose if necessary.

To attach the Hansen fittings (quick-disconnect fittings):

Grasp the quick-disconnect female Hansen socket of the connecting

hose

Содержание Norm-O-Temp 111W



















































































Результаты поиска

Содержание Norm-O-Temp 111W

Отзывы:

Похожие инструкции для Norm-O-Temp 111W

Бренды по названию

Популярные бренды

CSZ Norm-O-Temp 111W, Руководство по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание Norm-O-Temp 111W

Отзывы:

Похожие инструкции для Norm-O-Temp 111W

Бренды по названию

Популярные бренды