CrustBuster 3200 Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 56

CrustBuster 3200 Скачать руководство пользователя страница 18

Assembly Instructions

40' Drill

STEP 11 Attach pull bar slides to each side of A-

frame in front of cross tube with
1/2" x 4 1/2" HHCS, lock washer, and hex
nut.

STEP 12 Install a 3" x 8" hydraulic cylinder (base

end  to  frame  --  ram  end  to  wheel  lug  --
ports  to  top  of  drill)  to  wing  wheel
rockershaft.    Install  5-bolt  rim  and  tire
assemblies  to  hubs.    Follow  the  same
procedure on opposite wing rockershaft.

STEP 13 Mount selector valve plate to selector

valve bracket with two (2) 3/8" x 1" HHCS,
nuts,  and  lock  washers.    Attach  valve  to
plate  with  two  (2)  5/16"  x  1"  HHCS  and
lock  washers.    Valve  is  mounted  with
handle up and two port side forward.  Intall
fittings and hoses

per Figure 13 on page 4

.

Use  hose  clamps  to  attach  hoses  along
front  of  frames.    These  are  attached  to
walkboard and tooth clamp bolts.  Cable
wrap and hose carriers hold hoses which
are routed down top of A-frame.  Slack in
hoses going to wing cylinders is needed at
the hinge.  Attach a hose clamp on front
bolt  of  inside  wing  box  standoff  to  hold
hoses up over hinge area.

STEP 14 WING LEVEL ADJUSTMENTS. Activate

hydraulics to wing and center frame cylin-
ders to raise drill. Level top of 4" x 6"
center frame tube using hitch jack.

(Refer

to Figure 14.)

Check each wing about

midway out on 4" x 6" tube to make sure it
is level.  If wings require leveling, remove
two  (2)  3/8"  bolts  which  hold  large  hex
plate on top of hinge.  Loosen set screw in
side  of  1  1/2"  hex  nut  and  loosen  nut.
Hinges are set at factory at zero degrees.

This is indicated by two small holes in
hex plate pointing outward toward
wing.

To tip wing FORWARD, turn indica-

tor holes to front of drill. To tip wing
BACKWARDS, turn indicator holes to back
of drill. Level both wings and re-secure
3/8" bolts, 1 1/2" nut, and set screws.

STEP 15 FOLD ADJUSTMENTS. Install cylinder

lockout  in  center  frame  cylinder  and  se-
cure with 5/16" x 2 3/4" pin.  Switch selec-
tor valve to fold cylinder.  Slowly fold drill
checking  for  clearances  and  binding.    If
wings do not fold fully, adjust clevis on end
of fold cylinder.  Screw out to fold further,
and in so wing does not fold in as far.

Raise latches on wing carrier and secure
with 3/4" pins. Raise wing wheels and drill
is ready for transport.

Figure 14

16

«
...
16
17
18
19
20
...
»

Содержание 3200

























































Отзывы:

Нет отзывов