CrustBuster 3200 Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 56

CrustBuster 3200 Скачать руководство пользователя страница 13

Assembly Instructions

32' Drill

STEP 7

(Refer to Figure 7)

Install  hitch  on  front  of  A-frame  (lug  on
hitch goes on top, pointing to back of drill)
with 1 1/2" x 9 1/2" pin.  Clevis is attached
to  front  of  hitch  with  1  1/2"  x  9  1/2"  pin.
These  pins  are  secured  with  5/16"  x  3"
HHCS and lock nuts.  Install ratchet turn-
buckle between lug on A-frame and lug on
hitch with pins provided with turnbuckle.

Install hose carrier on side of hitch lug with
two (2) 1/2" x 2" HHCS, lock washers, and
hex nuts.

Figure 7

STEP 8

(Refer to Figure 8)

Lift  wing  frame  assembly  at  point  of  bal-
ance  and  align  U-shaped  part  on  wing
frame  with  spool  on  center  frame  hinge.
Insert 1 1/2" x 11 3/8" hinge pin (pin with
square head) from front so small stop on
wing  frame  keeps  pin  from  turning.    Se-
cure  with  1  1/2"  hex  nut.    Tighten  set
screw in nut.  Lower wing to ground.  At-
tach plastic tube on inside cup of drill box
to  shank  feed  tube  located  on  hinge.
Secure  with hose clamp.  Use the same
procedure to assemble opposite wing.

Figure 8

STEP 9

(Refer to Figure 9)

Front pull bars are installed between plates
of  fold  lug  located  on  front  of  A-frame.
The front pull bars are right and left.  They
are installed with fold arm clevis up and to
outside  of  A-frame.    They  are  attached
with 1 1/2" x 11 3/8" pins.  (round washer
head) and 3/8" x 3 1/2" cotter pins.

Figure 9

STEP 10

(Refer to Figure 10)

Swivel ball end of rear pull bar mounts
between plated on rear of front pull bars.
Secure with 1" x 6 1/2" HHCS installed

with head down

and lock nuts.

Attach clevis end of rear pull bar to swivel
ball plate on front of wings with 1" x 4"
HHCS and lock nuts.

Figure 10

11

«
...
11
12
13
14
15
...
»

Содержание 3200

























































Отзывы:

Нет отзывов