Crown FME 1000W, Руководство пользователя

Страница: 73 / 132

Crown Broadcast FME 350W to 2000W User Manual– 05/2013
Page 73
Crown Broadcast, a division of International Radio & Electronics Corporation 25166 Leer Drive, Elkhart, Indiana, 46514-5425 USA
Ph +1 (574) 262 8900
NAME
Access
(R/W)
Possible value on the
serial port of the unit
Comments
INPUT.LINE1.LEVEL R/W -20.00...18.00
Internal numerical gain. For AES, between -20 and
0; for ANA between -18 and +18
INPUT.LINE1.PREAC R/W 0;50;75 Sets the value of the pre-emphasis
INPUT.LINE1.PRESENCE R
"NONE" or "L" or "R" or
"L&R"
Indicates audio signals are present on input 1
INPUT.LINE1.RIGHT.PEAK R -100 … 28
Gives the right audio input max peak value over 100
milliseconds
INPUT.LINE1.RIGHT.PKMAX R -100 … 28
Gives the right audio input max peak value over 1
second.
INPUT.LINE1.SW.BACKDELA
Y
R/W XXX=[0…30]
Back delay on the channel with the highest
configurable priority.
INPUT.LINE1.SW.DELAY R/W XXX=[1…120] Switching delay when loss of audio 1
INPUT.LINE1.SW.PRIO
R/W 0..7 ; 0=disabled Priority of each audio channel (7= highest priority)
INPUT.LINE1.SW.SILENCE R/W
"L" or "R" or "ANY" or
"BOTH"
Sets on which channel (L,R or L+R) silence
detection must be conducted for the audio input 1
INPUT.LINE1.SW.THRESH R/W -90…000 Silence triggering level in dBFS on channel 1
INPUT.LINE1.TRIM R/W -3.00 to 3.00
Sets the offset between left and right channels (+3 =
left channel level is 3 dBu higher than right channel
level)
INPUT.LINE1.TYPE R "ANA" or "AES" "OFF"
Indicates the type of audio signals present on input
1
INPUT.LINE2.DRIVE R/W -6.00 to 6.00
Drive setting, allows an increase of the input audio
level without changing the deviation setting.
INPUT.LINE2.FLT R/W 0;1;2 0=15;1=16;2=17 Configuration of the audio filter
INPUT.LINE2.LEFT.PEAK R -100 … 28
Gives the right audio input max peak value over 100
milliseconds
INPUT.LINE2.LEFT.PKMAX R -100 … 28
Gives the right audio input max peak value over 1
second.
INPUT.LINE2.LEVEL R/W -20.00...18.00
Internal numerical gain. For AES, between -20 and
0; for ANA between -18 and +18
INPUT.LINE2.PREAC R/W 0;50;75 Sets the value of the pre-emphasis
INPUT.LINE2.PRESENCE R
"NONE" or "L" or "R" or
"L&R"
Indicates audio signals are present on input 2
INPUT.LINE2.RIGHT.PEAK R -100 … 28
Gives the right audio input max peak value over 100
milliseconds
INPUT.LINE2.RIGHT.PKMAX R -100 … 28
Gives the right audio input max peak value over 1
second
INPUT.LINE2.SW.BACKDELA
Y
R/W XXX=[0…30]
Back delay on the channel with the highest
configurable priority.
INPUT.LINE2.SW.DELAY R/W XXX=[1…120] Switching delay when loss of audio 2
INPUT.LINE2.SW.PRIO
R/W 0..7 ; 0=disabled Priority of each audio channel (7= highest priority)
INPUT.LINE2.SW.SILENCE R/W
"L" or "R" or "ANY" or
"BOTH"
Sets on which channel (L,R or L+R) silence
detection must be conducted for the audio input 2
INPUT.LINE2.SW.THRESH R/W -90…000 Silence triggering level in dBFS on channel 2
INPUT.LINE2.TRIM R/W -3.00 to 3.00
Sets the offset between left and right channels (+3 =
left channel level is 3 dBu higher than right channel
level)
INPUT.LINE2.TYPE R "ANA" or "AES" "OFF"
Indicates the type of audio signals present on input
2
INPUT.MPX.SW.BACKDELAY R/W XXX=[0…30]
Back delay on the channel with the highest
configurable priority.
INPUT.MPX.SW.DELAY R/W XXX=[1…120] Switching delay when loss on the MPX input
INPUT.MPX.SW.THRESH R/W -90…000 Silence triggering level in dBFS on MPX 1
INPUT.MPX1.DRIVE R/W -6.00 to 6.00
Drive setting, allows an increase of the input audio
level without changing the deviation setting.
INPUT.MPX1.LEVEL R/W -18.00...+18.00 Internal numerical gain
INPUT.MPX1.PEAK R -150…150
Gives the deviation max peak value of the
transmitted signal in kHz over 100 milliseconds
INPUT.MPX1.PKMAX R -150…150
Gives the deviation max peak value of the
transmitted signal in kHz over 1 second