Creative Playthings Williamsburg Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 20

background image

Assembly

© Copyright 2005, Creative Playthings

Williamsburg
19687-100 rev s (10-17)

Page 10

ASSeMbly inStruCtionS

SteP 3 - left & right Platform Sides:

Fasten a Platform side (Q) to the Corner Posts (F) above

either of the sandbox sides (T) using one 5/16 x 4" hex bolt

assembly through the top holes (only) on each end.

Fasten the left Platform side (Q) to the Corner Posts (F) op-

posite the right Platform side using one 5/16 x 4" hex bolt

assembly through the top holes (only) on each end. Fasten

the Platform side in the position as shown in the illustration.
do not tighten fasteners completely, they may need to be

loosened to install Tent Pipes in a later step.

Q

Q

T

left

right

Front

back

left

Front

back

«
...
8
9
10
11
12
...
»

Содержание Williamsburg





















Отзывы:

Нет отзывов

Похожие инструкции для Williamsburg

Бренд: BACtrack Страницы: 13

Бренд: EuroLite Страницы: 28

Бренд: Major tech Страницы: 12

Бренд: GSWeb Playground Equipment Страницы: 20

Бренд: ultraMEDIC Страницы: 28

NOVACAT X8 COLL

Бренд: Pottinger Страницы: 91

TRACER pH PockeTester 1741

Бренд: LaMotte Страницы: 16

Бренд: Psiber Страницы: 16

Бренд: Cutler-Hammer Страницы: 45

THE FLASH JUKE 12

Бренд: N-Gear Страницы: 28

Бренд: SANDORA Страницы: 16

Бренд: MAHLE Страницы: 6

Бренд: Qtx Страницы: 2

Бренд: Rohde & Schwarz Страницы: 49

Бренд: Vatech Страницы: 85

Бренд: Innova Страницы: 24

Бренд: 2MamaBees Страницы: 8

FTB 88000 Series

Бренд: EXFO Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды