Creative Playthings Williamsburg Скачать руководство пользователя страница 19

Страница: 19 / 20

Assembly

Williamsburg

19687-100 rev s (10-17)

Page 19

ASSeMbly inStruCtionS

illustration #1

SteP 28 - tent:

Tent: drape the Tent (aC) over the three

center Tent Pipes with the hem facing down.

slide one 61" Tent Pipe (ab) through the pock-

et at each end of the Tent (aC). insert the ends

of the Tent Pipes (ab) into the holes in the end

Tent supports (X), as shown. loosen the bolts

securing the front end Tent support to fit the

Tent Pipes into place. re-tighten the hardware

when the Tent Pipes are seated.

SteP 29 - Secure tent Pipes:

use a 1/8" diameter high speed steel drill to bore a pilot

hole through the bottom of a end Tent support and one wall

of the steel Tent Pipe, as shown. secure the Tent Pipe to

the end Tent support using one #10 x 2-1/2" Wood screw.

repeat with the other three ends of the Tent Pipes.

SteP 30 - Hole Caps:

make a final check and make sure that all the bolts and

screws have been tightened.
locate the 1" hole Caps in the hardware bag. install hole

Caps into all the counter-bored holes to cover and protect

the hardware.

Содержание Williamsburg




















Результаты поиска

Содержание Williamsburg

Отзывы:

Похожие инструкции для Williamsburg

Бренды по названию

Популярные бренды

Creative Playthings Williamsburg, Инструкция по сборке

Результаты поиска

Содержание Williamsburg

Отзывы:

Похожие инструкции для Williamsburg

Бренды по названию

Популярные бренды