Creative Playthings Williamsburg Скачать руководство пользователя страница 5

Страница: 5 / 20

Assembly

Williamsburg

19687-100 rev s (10-17)

Page 5

Pre ASSeMbly inforMAtion

Lag Screw

Flat Washer

CreAtiVe PlAytHingS PlAy SetS uSe A few StAndArd ConneCtionS.

beCoMing fAMiliAr witH tHeSe ConneCtionS will SiMPlify ASSeMbly And

inSure A SAfer PlAy ProduCt for your CHildren.

Hex bolt & weld nut Assembly Procedure:

typical installation - lag Screws:

• Tap the head of the lag

screw with a hammer to start

the threads into the wood and

then use a 9/16" socket to

tighten.

• do noT over tighten

typical installation - wood Screws:

•  use an electric drill or screw gun to drive screws.
•  drill 1/8" pilot holes where required.
•  We recommend that you lubricate the

threads of the screws with beeswax or

soap to ease installation and minimize

breaking screws.

•

it is very important to make cer-

tain that the tops of all screws are

flush with the surface of the wood

and there are no protruding sharp

edges.

Assembly layout:

align the holes in the parts to be fastened. start prelimi-

nary tightening of bolt into weld nut by hand. Tighten each

bolt with a wrench until the lock washer is fully compressed

between the head of the bolt and the flat washer.

Correct Assembly:

bolt has been screwed securely into weld nut and the con-

nection is tight. Check connections periodically for tight-

ness during the life of the play set .

do not over tighten.

incorrect Assembly:

during assembly or maintenance the bolt protrudes 1/8"

past the weld nut. Call customer service or replace the

bolt at a local hardware store. You may be overtightening

or using the wrong size bolt.

failure to replace this bolt with a shorter one could

result in serious injury.

All hardware on this set is specially coated for corrosion

resistance. if non-Creative Playthings hardware is used, it MuSt be

galvanized or stainless steel.

Содержание Williamsburg




















Результаты поиска

Содержание Williamsburg

Отзывы:

Похожие инструкции для Williamsburg

Бренды по названию

Популярные бренды

Creative Playthings Williamsburg, Инструкция по сборке

Результаты поиска

Содержание Williamsburg

Отзывы:

Похожие инструкции для Williamsburg

Бренды по названию

Популярные бренды