
32
COSMOGAS
AGUAPLUS
12 - INSTALLATION - External cover
12.1 - Installation of external cover
ATTENTION
:
The small parts in this kit will have the following
references:
- Screw 6x20 will be indicated with “A”;
- Screw 4x10 will be indicated with “B”;
- Screw 4x25 will be indicated with “C”;
- Screw 4x20 will be indicated with “D”.
ATTENTION
:
Overtightening of screws “C” may lead to deformation of
the panel on which they are applied.
For installation of the external cover, proceed as follows:
1.- Use a spanner to loosen the adjustable feet “T” on the
appliance (figure 12-1), insert bracket “H” and re-tighten
the adjustable feet “T” (figures 12-2 and 12-3). Repeat this
procedure on the opposite side.
2.- Remove the lower and upper front coverings “F” and the
upper covering “U” from the appliance, as shown in figure
12-4.
3.- Insert the lower frame “J” (figure 12-5) and secure it to
bracket “H” with the screws “A” through the holes (figure
12-6).
4.- Insert the lower and upper front coverings “F” on the
appliance (figure 12-7). Then adjust the adjustable feet
“I” on the lower frame “J” to stabilise it on the installation
surface (figure 12-8).
5.- Insert the four tubes “K” over the pins on the lower frame
“J” using a rubber hammer (figures 12-9 and 12-10).
6.- Insert the upper frame “G” of the outdoor covering using
a rubber hammer (figure 12-11).
7.- Insert the upper fixing brackets “Q” (figures 12-12 and 12-
13). Then insert screw “A” with nut “E” to fasten the brackets
to the appliance (figure 12-14) and screw “B” to fasten the
brackets to the frame of the outdoor covering (figure 12-15).
8.- Remove the pre-cut discs AG and AH , as shown in
figures 12-16 and 12-17, and according to the type of
electrical and condensate disposal system present at the
appliance’s installation site, the pre-cut discs “X” and “Y”
can be removed from the covering AG
in figure 12-18.
9.- Insert coverings AG and AH
in the way shown in figures
12-18 and 12-19 and secure them to the structure with
screws “C” (figure 12-20). Then fit the rain protection grille
“R” with screws “B”, as shown in figure 12-21.
10.- Fit the metal plate “S” on the covering AH with screws “B”
(figure 12-22) and fit the metal plates
AA on the covering
AG with screws “B” and “C” to fasten them; inserting them
as shown in figure 12-22.
11.- Position the side coverings AM (before) and AL (after),
and secure them to the structure with screws “C” (figure
12-23).
12.- Fit the upper covering AE to the upper frame “G”, with
screws “B” (figures 12-24 and 12-25).
13.- Use screws “D” to fasten the guard for electrical
connections “L”, for intake “M” and for exhaust “N” (or “P”)
to the upper covering (figures 12-26 and 12-27); remember
to insert gaskets “O” and “W” as shown in figure 12-26.
ATTENTION
:
- If you have a 110 mm diameter flue exhaust, use the
covering for exhaust “N” in figure 12-26.
- If you have an 80 mm diameter flue exhaust, use the
covering for exhaust “P” in figure 12-26.
14.- Place the front coverings AP (before) and AN (after),
in the way shown in figures 12-28 and 12-29. Fasten them
to the structure by adjusting locks “Z” with a flat head
screwdriver (figure 12-30).
15.- Finally, fasten the metal plates AR and AS , with screws
“B”, to the lower covering “J”; as shown in figures 12-31
and 12-32.
Содержание AGUAPLUS 100
Страница 79: ......
Страница 80: ...COSMOGAS s r l Via L da Vinci 16 47014 MELDOLA FC ITALY info cosmogas com www cosmogas com...