Cosmed Quark CPET Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 102

background image

16 - Getting Started - System Overview



System Overview

The Quark Series consists of the following main parts:

•

Quark unit

•

Flowmeter

•

Breathing valve (if required)

•

Additional external sensors and devices (temperature-humidity, HR, oximeter)



Quark Unit

The Quark unit contains the following elements:

•

Power switch (located on the front panel)

•

Connectors and ports (located on the rear panel)

Powering on the device

When the unit is plugged in, press the power switch on the front panel. The green led above the switch will turn on, indicating that the Quark is on

Powering off the device

Press the power switch on the front panel. The green led above the switch will turn off, indicating that the Quark is no longer powered on



Flowmeter(s)

Turbine Flowmeter

The turbine flowmeter assembly consists of a bidirectional turbine and an optoelectronic reader. The reader measures infrared light interruptions
caused by the spinning blade inside the turbine. The device may be used to measure a wide flow range and is not affected by ambient conditions
(pressure, humidity, room temperature, exhaled gas concentration). Daily calibration of the turbine is not necessary, however calibrations should be
performed regularly to ensure accurate measurements.

There are three turbine flowmeters: ID28, ID28 Spiro and ID18.

VO

2

max

«
...
16
17
18
19
20
...
»

Содержание Quark CPET







































































































Отзывы:

Нет отзывов

Похожие инструкции для Quark CPET

Бренд: Salvis Страницы: 40

Бренд: IDEAL Страницы: 2

Бренд: Harken Страницы: 4

Бренд: Raven Страницы: 17

Бренд: Campbell Страницы: 12

Бренд: Gardner Bender Страницы: 8

Бренд: NARIKA Страницы: 2

Бренд: TATU Страницы: 30

Бренд: Rane Страницы: 4

Бренд: Sabio Страницы: 182

Бренд: ZacUrate Страницы: 2

Бренд: ZacUrate Страницы: 2

Бренд: Vaillant Страницы: 76

Бренд: H2flow Страницы: 2

Бренд: V-TAC Страницы: 27

Бренд: Yacht Sentinel Страницы: 32

Бренд: X-FLOC Страницы: 35

Бренд: Goobay Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды