Cormach MEC 200 TRUCK, Руководство по эксплуатации и обслуживанию

Страница: 40 / 44

Use and Maintenance Manual – 09/2016 Rel. 0 Page 34
20.1 Error Codes
The machine indicates error conditions by alternating the display of the error code with a brief description (in English) pf the cause
of the error.
The list of error codes and brief descriptions are reported in table T20.1. The machine displays the code for different times depending
on the code of said error, as indicated in the “Error displayed” column in table T20.1.
Table T20.1: Error codes
Error
code
Brief description Error
displayed (1)
Description Notes
000 a 009 INT ERR
Machine parameters internal error. Contact technical support.
010 REV SPN Reverse rotation of the wheel. Contact technical support.
012 NO STP The wheel cannot be stopped at the
end of the launch.
Check the mains voltage. If the checks do not
lead to any results, contact technical support.
014 NO SPN The wheel does not spin. Contact technical support.
015 (Codice del tasto
incastrato)
PERMANENT
UNTIL TURNED
OFF
Keypad blocked at start-up. Release all buttons, then turn off or restart the
machine. If the error persists, contact technical
support.
018 NO BTI Cannot communicate with the
expansion board.
Turn the machine off and the on again. If the
error persists, contact the technical support.
019 NO CP OPERATOR
CONFIRMATION
Communication processor failure. Turn the machine off and then on again. If the
error persists, contact technical support.
The machine can still be used but all functions
related to the USB port are disabled.
020 NO EEP OPERATOR
CONFIRMATION
Lack of communication with the
eeprom memory.
Turn the machine off and then on again. If the
error persists, contact technical support.
021 EEP ERR OPERATOR
CONFIRMATION
Lack of machine calibration data or
incorrect calibration data.
Carry out calibration for the CAR/SUV Wheel
Type and/or for the MOTO Wheel Type. If the
error persists, contact technical support.
See also ERR 030 and ERR031.
022 a 024 OPERATOR
CONFIRMATION
Error during calibration. Excessive imbalance or anomaly. Turn the
machine off and then on again. If the error
persists, contact technical support.
026 NO –A- OPERATOR
CONFIRMATION
A launch without weight or failure of
the pick-up A signal in the Cal2
calibration phase.
Apply the intended weight and repeat the
launch. If the error persists, contact technical
support.
027 NO –B- OPERATOR
CONFIRMATION
A launch without weight or failure of
the pick-up B signal in the Cal2
calibration phase.
Apply the intended weight and repeat the
launch. If the error persists, contact technical
support.
028 INN IMB OPERATOR
CONFIRMATION
Launch with weight on the internal
side during the Cal3 calibration phase.
In this phase, the weight must be on
the external side.
Remove the weight from the internal side and
repeat the launch. If the error persists, contact
technical support.
030 CAR CAL OPERATOR
CONFIRMATION
Lack of calibration data for the
CAR/SUV Wheel Type.
Carry out calibration for the CAR/SUV Wheel
Type.
031 TRC CAL OPERATOR
CONFIRMATION
Lack of calibration data for the TRUCK
(motorbike) Wheel Type.
Carry out machine calibration for the TRUCK
Wheel Type.
051 TOO FAR OPERATOR
CONFIRMATION
Hidden Weights program: the
selected point is too far from the
external imbalance position.
The point must be included up to 120° from the
external imbalance position. See chapter 16.
052 NOT INC OPERATOR
CONFIRMATION
Hidden Weights program: the
external imbalance position is not
between the selected W1 and W2
points.
Choose W1 and W2 points so that they include
the external imbalance position. See chapter
16.
054 Cannot communicate with the motor
inverter.
Turn the machine off and the on again. If the
error persists, contact the technical support.
055 NO OPT OPERATOR
CONFIRMATION
The static imbalance of the wheel is
too low: the Optimization program
cannot be used.
Turn the machine off and the on again. If the
error persists, contact the technical support.
056 HIG TMP Motor inverter overtemperature. Turn the machine off, wait at least 10 minutes
and then turn the machine on again. If the error
persists, contact the technical support.
057 OVR VOL Motor inverter overvoltage. Turn the machine off and the on again. If the
error persists, contact the technical support.
058 UND VOL Motor inverter undervoltage. Turn the machine off and the on again. If the
error persists, contact the technical support.
059 SOV RA Motor inverter overload. Turn the machine off and the on again. If the
error persists, contact the technical support.