background image

3. After an Alarm 

Page 20 

496930 

To reinstate a zone repeat steps 1 to 4. At step 3 press 

Y

 and “o” will 

disappear. Press 

X

 to exit.  

Omissions are not permanent. When you unset the system the control unit 
reinstates all omitted zones for the level you have unset. 

Access Codes 

The system can store up to 16 different user access codes. For security you 
should give one code to each person who has responsibility for setting and 
unsetting the system. Do not allow users to share codes. 

Every time someone enters an access code on the keypad the system 
records the event in its log. To distinguish all the users and keep their 
access codes hidden, the log shows each user as a number, for example 
"User 02", "User 03" and so on.  

When delivered from the factory all access codes are set to default numbers. 
User 01 default access code is "1234". You should change this immediately 
to a code that only you know. User 01 is the only access code that can 
change other access codes. 

User 02 default access code is "

X

 002", User 03 is "

X

 003" and so on up to 

User 16 (

X

 016). However, the default access codes for these users cannot 

set or unset the system, or use any of its special functions. 

Duress Code 

If your system is connected to a communication device, you may want to 
give some of the users a 

Duress Code 

as well as their normal access code. 

If a user enters the Duress Code to unset the system, then the control unit 
sends a silent Panic alarm call to the communication device. The Duress 
Code is designed for times when a user is being forced to unset the alarm 
system by an intruder. 

The default Duress Code is "

X

017". This code is inactive until you change it. 

5.  Key in your access code (or present a tag) and press a Level key.. 

6.  The control unit gives an error tone and the 

display shows (for example): 

 

7.  Press 

Y

If necessary, press 

Y

 again for each omitted zone shown on the 

display. 
(If you wish to escape press 

X

.) 

 

After you press 

Y

 for the final omitted zone the control unit starts to 

set. 

A:Omit Zone 07? 

Содержание Menvier 9651





























Отзывы: