manualshive.com logo in svg

CoolBot Walk-in Cooler, Руководство по монтажу

Поделиться
Скачать
CoolBot Walk-in Cooler Скачать руководство пользователя страница 5

 

 

 

 

PHONE: 888-871-5723 

 

 

[email protected] 

 

2018 © Store It Cold, LLC. 

Rev 2018-9a 

All Rights Reserved.  

A/C UNIT 1 YEAR LIMITED WARRANTY 

Your A/C unit carries a 1 Year limited warranty. 

Please contact SIC to facilitate a warranty 

claim of your A/C unit during this period

. 

IMPORTANT!

 

Please refer to the OWNERS’S MANUAL of the A/C unit to follow 

recommendations about proper installation, operation, and maintenance of your A/C unit.  

This warranty will NOT cover claims due to improper installation or improper electrical supply 
to the A/C unit. 

 

 

COOLBOT DIGITAL CONTROLLER 1 YEAR LIMITED WARRANTY 

DISCLAIMER

: By using the CoolBot temperature controller, you (the “User”) acknowledge there 

are inherent hazards in getting an air-conditioner 

(“A/C”) to do something it was not originally 

designed to do, and that these inherent hazards cannot be ameliorated, mitigated or obviated 
while still maintaining the essential functionality of the CoolBot. User accepts all responsibility in 
the use of and monitoring of the CoolBot and A/C. User assumes all risk of loss of property or 
product due to improper functioning of the CoolBot (or A/C). User assumes all risk of injury and 
warrants  that  he/she  will  defend,  indemnify  and  hold  the  seller  harmless  for  any  direct  or 
consequential harm or damage that may result from the use of this product.  

LIMITED WARRANTY:

 CoolBots are warranted against defects for 1 year, not including damage 

due to misuse or accidents. To double the warranty on your CoolBot see page 19 of the CoolBot 
Installation Manual. 

 

 

 

ALL COOLBOT WALK-IN COOLER SALES ARE FINAL INCLUDING ALL ITS COMPONENTS - 

ENCLOSURE, A/C UNIT AND COOLBOT DIGITAL CONTROLLER. 

 

 

 

 

 

Содержание Walk-in Cooler































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды