CoolBot Walk-in Cooler Скачать руководство пользователя страница 3

Страница: 3 / 30

PHONE: 888-871-5723

[email protected]

2018 © Store It Cold, LLC.

Rev 2018-9a

IMPORTANT!

INSPECT SHIPMENT IMMEDIATELY UPON ARRIVAL FOR LOSS OR DAMAGE. LOOK FOR TEARS ON

THE PLASTIC WRAPPING, DENTS, CUTS, OR ANY VISIBLE DAMAGE ONCE THE LOAD IS ON THE

GROUND BEFORE IT MOVES IN TO YOUR LOCATION AND BEFORE YOU SIGN THE RECEIPT.

PLEASE WRITE ANY DAMAGES AND/OR DISCREPANCIES ON BILL OF LADING BEFORE SIGNING
AT THE TIME OF DELIVERY AND

TAKE PHOTOS OF THE LOAD FROM EVERY SIDE

TO SUPPORT

YOUR CLAIM.

If concealed loss or damage is discovered later, notify your Store It Cold representative and
submit pictures of the damage.

IMPORTANT!

AIR CONDITIONER

INSPECT A/C IMMEDIATELY UPON ARRIVAL FOR DAMAGE. LOOK FOR TEARS OR CUTS, OR ANY

VISIBLE DAMAGE ON THE BOX ONCE THE A/C HAS BEEN UNLOADED AND BEFORE YOU SIGN

THE RECEIPT. IF THERE IS ANY NOTICEABLE DAMAGE REFUSE THE DELIVERY AND CONTACT US

IMMEDIATELY TO ARRANGE FOR DELIVERY OF A REPLACEMENT UNIT.

CAREFULLY OPEN YOUR A/C WITHIN 24HR AND INSPECT FOR CONCEALED DAMAGE AND FOR
MISSING CONTENTS. IN CASE OF CONCEALED DAMAGE OR MISSING PARTS,

DO NOT PLUG IN

YOUR UNIT

. PLEASE

TAKE PICTURES

AND NOTIFY US WITHIN THE 24HR PERIOD SO WE CAN

HAVE A REPLACEMENT A/C BE DELIVERED.

Содержание Walk-in Cooler





























Результаты поиска

Содержание Walk-in Cooler

Отзывы:

Бренды по названию

Популярные бренды

CoolBot Walk-in Cooler, Руководство по монтажу

Результаты поиска

Содержание Walk-in Cooler

Отзывы:

Бренды по названию

Популярные бренды