manualshive.com logo in svg

CoolBot Walk-in Cooler, Руководство по монтажу

Поделиться
Скачать
CoolBot Walk-in Cooler Скачать руководство пользователя страница 20

 

 

 

 

PHONE: 888-871-5723 

 

 

[email protected] 

 

2018 © Store It Cold, LLC. 

Rev 2018-9a 

All Rights Reserved.  

ROOF MEMBRANE (OUTDOOR UNITS ONLY) 
 

IMPORTANT

 

Improper installation may result in water accumulation or water infiltration through the 
membrane. SIC recommends the roof membrane to be installed by a contractor to ensure it is 
installed correctly. 
 

MEMBRANE INSTALLATION ON SMALL COOLERS - ALL SIDES ARE LESS THAN 10FT

 

1.

 

Extend your membrane on the roof of your walk-in with the soft 

smooth semi-glossy 

textured side UP (overlapping seams DOWN)

. Ensure that it hangs approximately the 

same amount on all sides. Don’t worry if it is too long, it can be trimmed after it’s 

installed in place. 

 

2.

 

Starting at the front of the cooler, pull down on the membrane and secure to the wall by 
installing the metal trimming provided. Screw the metal trimming to the front side using 
the self-drilling hex sheet metal screws provided in your installation kit.  

 
IMPORTANT!

 Make sure the trim is level and 

below the seam

 in between the wall panel 

and the ceiling panel

. It’s important that this seam stays under the membrane.

 

 

3.

 

Repeat the same process for the back side of the cooler. 

4.

 

After the front and back part of the membrane have been secured, proceed to one of the 
sides of the cooler. Tuck the excess fabric at the front corner underneath the membrane 
to create a nice fold. Pull down tight and start securing the membrane to the wall panels 
following the same recommendations as before. Install the trimming at the same level as 
you did on the front and back to remain constant around the perimeter of the cooler. 
Work your way from front to back as you pull down tight and secure.  

Содержание Walk-in Cooler































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды