manualshive.com logo in svg

CoolBot Walk-in Cooler, Руководство по монтажу

Поделиться
Скачать
CoolBot Walk-in Cooler Скачать руководство пользователя страница 2

 

 

 

 

PHONE: 888-871-5723 

 

 

[email protected] 

 

2018 © Store It Cold, LLC. 

Rev 2018-9a 

All Rights Reserved.  

 

 

 

COOLBOT WALK-IN COOLER  

SHIPPING AND WARRANTY INFORMATION 

 

SHIPPING 

 
Please read carefully this document regarding your shipments for instructions on receiving, 
inspecting, and filing claims if necessary. 
 

•

 

Your CoolBot Cooler System will be delivered in ONE shipment which includes:  
1.

 

Enclosure (Walk-in box)  

2.

 

A/C unit  

3.

 

CoolBot Temperature Controller  

 

•

 

You will be provided with shipment information and estimated delivery times. 

 

•

 

Our Walk-In enclosure manufacturer and our A/C supplier take every precaution for safe 
arrival, but their responsibility ceases when shipment is turned over to the carrier. 

 

•

 

The walk-in cooler will be transported and delivered on a semi-truck. The receiver will be 
responsible for providing appropriate access to the delivery vehicle and all necessary 
equipment (or man power) to safely unload the pallets from the carrier.  

 

•

 

The receiver will be responsible for ensuring a solid surface for unloading the pallet where it 
can be rolled out of the lift gate and be left on the ground. 

 

 

 

 

Содержание Walk-in Cooler































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды